參數資料
型號: DS1868-100+
廠商: Maxim Integrated Products
文件頁數: 8/14頁
文件大小: 0K
描述: IC POT DIGITAL DUAL 100K 14-DIP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 25
接片: 256
電阻(歐姆): 100k
電路數: 2
溫度系數: 標準值 750 ppm/°C
存儲器類型: 易失
接口: 3 線串口
電源電壓: 2.7 V ~ 3.3 V,4.5 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 通孔
封裝/外殼: 14-DIP(0.300",7.62mm)
供應商設備封裝: 14-PDIP
包裝: 管件
DS1868
3 of 14
DS1868 BLOCK DIAGRAM Figure 1
I/O SHIFT REGISTER Figure 2
Transmission of data always begins with the stack select bit followed by the potentiometer-1 wiper
position value and lastly the potentiometer-0 wiper position value.
When wiper position data is to be written to the DS1868, 17 bits (or some integer multiple) of data should
always be transmitted. Transactions which do not send a complete 17 bits (or multiple) will leave the
register incomplete and possibly an error in the desired wiper positions.
After a communication transaction has been completed the RST signal input should be taken to a low
state to prevent any inadvertent changes to the device shift register. Once RST has reached a low state,
the contents of the I/O shift register are loaded into the respective multiplexers for setting wiper position.
A new wiper position will only engage after a RST transition to the inactive state. On device power-up,
wiper position will be random.
STACKED CONFIGURATION
The potentiometers of the DS1868 can be connected in series as shown in Figure 3. This is referred to as
the stacked configuration and allows the user to double the total end-to-end resistance of the part. The
resolution of the combined potentiometers will remain the same as a single potentiometer but with a total
of 512 wiper positions available. Device resolution is defined as RTOT /256 (per potentiometer); where
RTOT equals the total potentiometer resistance.
The wiper output for the combined stacked potentiometer will be taken at the SOUT pin, which is the
multiplexed output of the wiper of potentiometer-0 (W0) or potentiometer-1 (W1). The potentiometer
wiper selected at the SOUT output is governed by the setting of the stack select bit (bit 0) of the 17-bit I/O
shift register. If the stack select bit has value 0, the multiplexed output, SOUT, will be that of the
相關PDF資料
PDF描述
MS3456L22-2S CONN PLUG 3POS STRAIGHT W/SCKT
DS1847B-050+ IC RES TEMP-CNTRL 50/10K 16-BGA
MS3451W24-12P CONN RCPT 5POS CBL MNT W/PINS
GTC02R-20-15S CONN RCPT 7POS BOX MNT W/SCKT
MAX5499ETE+T IC DIG POT 10BIT 16-TQFN-EP
相關代理商/技術參數
參數描述
DS1868-100+ 功能描述:數字電位計 IC Dual RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1868-50 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1868-50+ 功能描述:數字電位計 IC Dual RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS1868BE-010+ 制造商:Maxim Integrated Products 功能描述:DUAL 256-STEP DIGITAL POTENTIOMETER - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC DGTL POT 10K 2CH 20TSSOP
DS1868BE-010+T/R 制造商:Maxim Integrated Products 功能描述:DUAL 256-STEP DIGITAL POTENTIOMETER - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC DGTL POT 10K 2CH 20TSSOP