- 您現在的位置：買賣IC網 > PDF目錄1913 > DS1881Z-050+T&R (Maxim Integrated Products)IC DGTL POT NV 2CH 45K 16-SOIC PDF資料下載
參數資料
| 型號： | DS1881Z-050+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DGTL POT NV 2CH 45K 16-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1,000 |
| 接片： | 64 |
| 電阻（歐姆）： | 45k |
| 電路數： | 2 |
| 溫度系數： | 標準值 750 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 帶卷 (TR) |
DS1881
Dual NV Audio Taper Digital Potentiometer
14
____________________________________________________________________
setup time (see Figure 4) before the next rising edge of
SCL during a bit read. The device shifts out each bit of
data on SDA at the falling edge of the previous SCL
pulse and the data bit is valid at the rising edge of the
current SCL pulse. Remember that the master gener-
ates all SCL clock pulses including when it is reading
bits from the slave.
Acknowledgement (ACK and NACK): An Acknowledge-
ment (ACK) or Not Acknowledge (NACK) is always the
9th bit transmitted during a byte transfer. The device
receiving data (the master during a read or the slave
during a write operation) performs an ACK by transmit-
ting a zero during the 9th bit. A device performs a
NACK by transmitting a one during the 9th bit. Timing
(Figure 4) for the ACK and NACK is identical to all other
bit writes. An ACK is the acknowledgment that the
device is properly receiving data. A NACK is used to
terminate a read sequence or as an indication that the
device is not receiving data.
STOP
CONDITION
OR REPEATED
START
CONDITION
REPEATED IF MORE BYTES
ARE TRANSFERRED
ACK
START
CONDITION
ACK
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
ACKNOWLEDGEMENT
SIGNAL FROM RECEIVER
SLAVE ADDRESS
MSB
SCL
SDA
R/W
DIRECTION
BIT
12
6
7
8
9
12
8
9
3–7
Figure 3. Data Transfer Protocol
SDA
SCL
tHD:STA
tLOW
tHIGH
tR
tF
tHD:DAT
tSU:DAT
REPEATED
START
tSU:STA
tHD:STA
tSU:STO
tSP
STOP
START
tBUF
NOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).
Figure 4. I2C Timing Diagram
相關PDF資料 |
PDF描述 |
|---|---|
| DS1882Z-050+T&R | IC POT DIGIT DL LOG 50K 16SOIC |
| DS1884AT+T | IC SFP PON ONU CTRLR 24TQFN |
| DS2105Z+ | IC SCSI TERMINATOR 16-SOIC |
| DS2106S/T&R | IC TERMINATOR SCSI 28-SOIC |
| DS2108S+T&R | IC TERM SCSI DIFF/SWITCH 24-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1882 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Dual Log Audio Digital Potentiometer |
| DS1882E-050 | 制造商:Maxim Integrated Products 功能描述:DUAL NV +/-5V AUDIO POT TSSOP-16 - Rail/Tube |
| DS1882E-050/T&R | 制造商:Maxim Integrated Products 功能描述:DUAL NV =/-5V AUDIO POT TSSOP 16 T& - Tape and Reel |
| DS1882E-050+ | 功能描述:數字電位計 IC Dual NV Audio Taper RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS1882E-050+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 64POS 45KOHM DUAL 16TSSOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT DIGIT DL LOG 50K 16TSSOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs Dual NV Audio Taper |
發布緊急采購，3分鐘左右您將得到回復。