- 您現在的位置：買賣IC網 > PDF目錄376962 > DS1921H-F5 High-Resolution Thermochron iButton PDF資料下載
參數資料
| 型號： | DS1921H-F5 |
| 英文描述： | High-Resolution Thermochron iButton |
| 中文描述： | 高分辨率Thermochron iButton的 |
| 文件頁數： | 30/44頁 |
| 文件大?。?/td> | 271K |
| 代理商： | DS1921H-F5 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
DS1921H/Z
30 of 44
INITIALIZATION PROCEDURE (RESET AND PRESENCE PULSES)
Figure 14
MASTER TX RESET PULSE
RESISTOR
MASTER
DS1921H/Z
t
RSTL
t
PDL
t
RSTH
t
PDH
MASTER RX PRESENCE PULSE
V
PUP
V
IHMASTER
V
TH
V
TL
V
ILMAX
0V
ε
t
F
t
REC
t
MSP
After the bus master has released the line it goes into receive mode (RX). Now, the 1-Wire bus is pulled
to V
PUP
via the pull-up resistor or, in case of a DS2480B driver, by active circuitry. When the threshold
V
TH
is crossed, the DS1921H/Z waits for t
PDH
and then transmits a presence pulse by pulling the line low
for t
PDL
. To detect a presence pulse, the master must test the logical state of the 1-Wire line at t
MSP
.
The t
RSTH
window must be at least the sum of t
PDHMAX
, t
PDLMAX
, and t
RECMIN
. Immediately after t
RSTH
is
expired, the DS1921H/Z is ready for data communication. In a mixed population network, t
RSTH
should
be extended to minimum 480μs at standard speed and 48μs at Overdrive speed to accommodate other 1-
Wire devices.
Read/Write Time Slots
Data communication with the DS1921H/Z takes place in time slots that carry a single bit each. Write time
slots transport data from bus master to slave. Read time-slots transfer data from slave to master. The
definitions of the write and read time slots are illustrated in Figure 15.
All communication begins with the master pulling the data line low. As the voltage on the 1-Wire line
falls below the threshold V
TL
, the DS1921H/Z starts its internal timing generator that determines when
the data line will be sampled during a write time slot and how long data will be valid during a read time
slot.
Master to Slave
For a
write-one
time slot, the voltage on the data line must have crossed the V
TH
threshold after the
write-one low time t
W1LMAX
is expired. For a
write-zero
time slot, the voltage on the data line must stay
below the V
TH
threshold until the write-zero low time t
W0LMIN
is expired. The voltage on the data line
should not exceed V
ILMAX
during the entire t
W0L
or t
W1L
window. After the V
TH
threshold has been
crossed, the DS1921H/Z needs a recovery time t
REC
before it is ready for the next time slot.
相關PDF資料 |
PDF描述 |
|---|---|
| DS1921Z-F5 | High-Resolution Thermochron iButton |
| DS1963L-F5 | NVRAM (Battery Based) |
| DS1963S | SHA iButton |
| DS1971 | 256-Bit EEPROM iButton |
| DS1973 | 4-kbit EEPROM iButton |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS1921H-F5# | 功能描述:iButton Thermochron High Res iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1921H-F5/A1C | 功能描述:iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1921H-F5+A1C | 功能描述:iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1921H-F50 | 功能描述:iButton RoHS:否 存儲類型:SRAM 存儲容量:512 B 組織: 工作電源電壓:3 V to 5.25 V 接口類型:1-Wire 最大工作溫度:+ 85 C 尺寸:17.35 mm x 5.89 mm 封裝 / 箱體:F5 MicroCan 制造商:Maxim Integrated |
| DS1921K | 功能描述:存儲器 IC 開發工具 RoHS:否 制造商:STMicroelectronics 產品:Reference Boards 工具用于評估:M24LR64-R 存儲容量:64 kbit 存儲類型:EEPROM 工作電源電壓:1.8 V to 5.5 V |
發布緊急采購，3分鐘左右您將得到回復。