- 您現在的位置：買賣IC網 > PDF目錄1914 > DS2105Z+ (Maxim Integrated Products)IC SCSI TERMINATOR 16-SOIC PDF資料下載
參數資料
| 型號： | DS2105Z+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/7頁 |
| 文件大小： | 0K |
| 描述： | IC SCSI TERMINATOR 16-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 類型： | SCSI，SE |
| 端子數： | 9 |
| 電源電壓： | 4 V ~ 5.25 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
DS2105
022698 2/7
FUNCTIONAL DESCRIPTION
The DS2105 consists of a bandgap reference, buffer
amplifier, and nine termination resistors (Figure 1). The
bandgap reference circuit produces a precise 2.55V
level which is fed to a buffer amplifier. The buffer pro-
duces a 2.85V level and is capable of sourcing at least
24 mA into each of the termination resistors when the
signal line is low (active). When the driver for a given
signal line turns off, the terminator will pull the signal line
to 2.85V (quiescent state). To handle actively negated
SCSI signals, the buffer can sink 200 mA, and VREF will
move less than 60 mV. When all lines settle in the quies-
cent state, the regulator will consume about 5 mA.
When the DS2105 is put into power–down mode by
bringing PD low, the power–down circuitry will turn off
the transistors on each signal line. This will isolate the
DS2105 from the signal lines and effectively remove it
from the circuit. The power–down pin (PD) has an inter-
nal 50K
pull–up resistor. To place the DS2105 into an
active state, the PD pin should be left open circuited.
To ensure proper operation, both the TERMPWR1 and
TERMPWR2 pins must be connected to the SCSI bus
TERMPWR line and both the VREF1 and VREF2 pins
must be tied together externally. Each DS2105 requires
a 4.7
F capacitor connected between the VREF pins
and ground. Figure 2 details a typical SCSI bus configu-
ration. In an 8–bit wide SCSI bus arrangement (“A”
Cable), two DS2105’s would be needed at each end of
the SCSI cable in order to terminate the 18 active signal
lines. In a 16–bit wide SCSI bus arrangement (“P”
Cable), three DS2105’s would be needed at each end of
the SCSI cable in order to terminate the 27 active signal
lines.
DS2105 BLOCK DIAGRAM Figure 1
GND
TERMPWR1
TERMPWR2
PD
POWER
DOWN
CIRCUITRY
50K ohm
BANDGAP
REFERENCE
110 ohms
R1
R2
R3
R4
R5
R6
R7
R8
R9
VREF1
VREF2
110 ohms
相關PDF資料 |
PDF描述 |
|---|---|
| DS2106S/T&R | IC TERMINATOR SCSI 28-SOIC |
| DS2108S+T&R | IC TERM SCSI DIFF/SWITCH 24-SOIC |
| DS2114Z | IC TERM SCSI 2% 150MIL 16-SOIC |
| DS2117MX/T&R | IC TERM SCSI LVD/SE ULT-3 FCHIP |
| DS2118MB+T&R | IC TERM SCSI LVD/SE ULT-3 36SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2105Z/T&R | 制造商:Maxim Integrated Products 功能描述:SCSI TERM. 5% 16P 150 MIL SO TRL - Tape and Reel |
| DS2105Z/T&R+C02 | 制造商:DSC 功能描述: |
| DS2105Z/T&R | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
| DS2105Z/T&R/C02 | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
| DS2105Z/T&R+C02 | 功能描述:SCSI 接口集成電路 RoHS:否 制造商:Texas Instruments 工作電源電壓:2.7 V to 5.25 V 電源電流:13 mA 最大工作溫度:+ 70 C 最小工作溫度:0 C 安裝風格:SMD/SMT 封裝 / 箱體:SSOP-36 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。