- 您現在的位置：買賣IC網 > PDF目錄97867 > DS2180A (MAXIM INTEGRATED PRODUCTS INC) DATACOM, FRAMER, PDIP40 PDF資料下載
參數資料
| 型號： | DS2180A |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Digital Transmission Controller |
| 英文描述： | DATACOM, FRAMER, PDIP40 |
| 封裝： | 0.600 INCH, DIP-40 |
| 文件頁數： | 33/35頁 |
| 文件大?。?/td> | 481K |
| 代理商： | DS2180A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁
DS2180A
7 of 35
ACB: ADDRESS COMMAND BYTE Figure 4
(MSB)
(LSB)
-
FRSR2
EYELMD
FM
SYELMD
B8ZS
B7
LPBK
SYMBOL
POSITION
NAME AND DESCRIPTION
-
CCR.7
Reserved, must be 0 for proper operation.
FRSR2
CCR.6
Function of REC Status Register 2.
0 = Detected B8ZS code words reported at RSR.2.
1 = COFA (Change-of-Frame Alignment) reported at RSR.2 when
last resync resulted in change of frame or multiframe alignment.
EYELMD
CCR.5
193E Yellow Mode Select.
0 = Yellow alarm is a repeating pattern set of 00 hex and FF hex.
1 = Yellow alarm is a 0 in the bit 2 position of all channels.
FM
CCR.4
Frame Mode Select.
0 = D4 (193S, 12 frames/superframe).
1 = Extended (193E, 24 frames/superframe).
SYELMD
CCR.3
193S Yellow Mode Select. Determines yellow alarm type to be
transmitted and detected while in 193S framing. If set, yellow
alarms are a 1 in the S-bit position of frame 12; if cleared, yellow
alarm is a 0 in bit 2 of all channels. Does not affect 193E yellow
alarm operation.
B8ZS
CCR.2
Bipolar eight zero substitution.
0 = No B8ZS.
1 = B8ZS enabled.
(Note: This bit must be set to 0 when CCR.1=1)
B7
CCR.1
Bit seven zero suppression. If CCR.1=1, channels with an all zero
content will be transmitted with bit 7 forced to 1. If CCR.1=0, no
bit 7 stuffing occurs.
(Note: This bit must be set to 0 when CCR.2=1)
LPBK
CCR.0
Loopback. When set, the device internally loops output transmit
data into the incoming receive data buffers and TCLK is internally
substituted for RCLK.
LOOPBACK (Refer to Figure 4)
Enabling loopback will typically induce an out-of-frame (OOF) condition. If appropriate bits are set in
the receive control register, the receiver will resync to the looped transmit frame alignment. During the
looped condition, the transmit outputs (TPOS, TNEG) will transmit unframed all 1's. All operating modes
(B8ZS, alarm, signaling, etc.) except for blue alarm transmission are available in loopback.
BIT SEVEN STUFFING
Existing systems meet 1's density requirements by forcing bit 7 of all zero channels to 1. Bit 7 stuffing is
globally enabled by asserting bit CCR.1 and may be disabled on an individual channel basis by setting
appropriate bits in TTR1–TTR3. Bit 7 stuffing and B8ZS modes should not be enabled simultaneously.
Enabling both results in LOS.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2180AN | DATACOM, FRAMER, PDIP40 |
| DS2181AN | DATACOM, FRAMER, PDIP40 |
| DS2181AQN | DATACOM, FRAMER, PQCC44 |
| DS2181A | DATACOM, FRAMER, PDIP40 |
| DS2181AQ | DATACOM, FRAMER, PQCC44 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2180A+ | 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2180AN | 功能描述:網絡控制器與處理器 IC T1 Transceiver RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2180AQ | 功能描述:網絡控制器與處理器 IC RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2180AQ/T&R | 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER-PLCC-TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TRANSCEIVER T1 44-PLCC 制造商:Maxim Integrated Products 功能描述:Network Controller & Processor ICs T1 Transceiver |
| DS2180AQ/T&R+ | 制造商:Maxim Integrated Products 功能描述:T1 TRANSCEIVER PLCC TRL LF - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。