- 您現在的位置：買賣IC網 > PDF目錄97867 > DS2187 (MAXIM INTEGRATED PRODUCTS INC) DATACOM, PCM TRANSCEIVER, PDIP18 PDF資料下載
參數資料
| 型號： | DS2187 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Digital Transmission Interface |
| 英文描述： | DATACOM, PCM TRANSCEIVER, PDIP18 |
| 封裝： | 0.300 INCH, DIP-18 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 330K |
| 代理商： | DS2187 |
MAX9010–MAX9013
SC70, 5ns, Low-Power, Single-Supply,
Precision TTL Comparators
8
_______________________________________________________________________________________
tional factor in resolution is the comparator’s stability in
its linear region. Many high-speed comparators are
useless in their linear region because they oscillate.
This makes the differential input voltage region around
zero unusable. Hysteresis helps to cure the problem
but reduces resolution (Figure 2). The devices do not
oscillate in the linear region and require no hysteresis,
which greatly enhances their resolution.
Applications Information
Power Supplies, Bypassing, and
Board Layout
These products operate over a supply voltage range of
4.5V to 5.5V. Bypass VCC to GND with a 0.1F surface-
mount ceramic capacitor. Mount the ceramic capacitor
as close as possible to the supply pin to minimize lead
inductance.
As with all high-speed components, careful attention to
board layout is essential for best performance. Use a
PC board with an unbroken ground plane. Pay close
attention to the bandwidth of bypass components and
place them as close as possible to the device.
Minimize the trace length and area at the comparator
inputs. If the source impedance is high, take the utmost
care in minimizing its susceptibility to pickup of unwant-
ed signals.
Input Slew Rate
Most high-speed comparators have a minimum input
slew-rate requirement. If the input signal does not
transverse the region of instability within a propagation
delay of the comparator, the output can oscillate. This
makes many high-speed comparators unsuitable for
processing either slow-moving signals or fast-moving
signals with low overdrive. The design of these devices
eliminates the minimum input slew-rate requirement.
They are excellent for circuits from DC up to 200MHz,
even with very low overdrive, where small signals need
to be resolved.
Figure 1. Timing Diagram
tH
tSU
tPD+
VIN
(DIFFERENTIAL)
LATCH
ENABLE (LE)
OUT
Figure 2. Effect of Hysteresis on Input Resolution
HYSTERESIS
BAND*
WITH HYSTERESIS
IDEAL (WITHOUT HYSTERESIS)
* WHEN HYSTERESIS IS ADDED, A COMPARATOR CANNOT RESOLVE ANY INPUT SIGNAL WITHIN THE HYSTERESIS BAND.
OUT
IN-
IN+
相關PDF資料 |
PDF描述 |
|---|---|
| DS2196LN | DATACOM, FRAMER, PQFP100 |
| DS21FF44 | DATACOM, FRAMER, PBGA300 |
| DS21FF44N | DATACOM, FRAMER, PBGA300 |
| DS21FT40N | DATACOM, FRAMER, PBGA300 |
| DS21FT40 | DATACOM, FRAMER, PBGA300 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2187+ | 功能描述:網絡控制器與處理器 IC Receive Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2187S | 功能描述:網絡控制器與處理器 IC Receive Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2187S/T&R | 制造商:Maxim Integrated Products 功能描述:IC RECEIVE LINE INTERFACE 20SOIC |
| DS2187S/T&R | 功能描述:網絡控制器與處理器 IC Receive Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS2187S+ | 功能描述:網絡控制器與處理器 IC Receive Line Interface RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。