- 您現在的位置：買賣IC網 > PDF目錄10908 > DS2250-32-16 (Maxim Integrated Products)IC MICROCNTRLR 32X8 16MHZ 40SIMM PDF資料下載
參數資料
| 型號： | DS2250-32-16 |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 12/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MICROCNTRLR 32X8 16MHZ 40SIMM |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | DS225x |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 16MHz |
| 連通性： | SIO，UART/USART |
| 外圍設備： | 電源故障復位，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器類型： | SRAM |
| RAM 容量： | 32K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.75 V ~ 5.25 V |
| 振蕩器型： | 外部 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 40-SIMM |
| 包裝： | 托盤 |
| 其它名稱： | DS22503216 |
DS2250(T)
3 of 18
PIN DESCRIPTION
PIN
DESCRIPTION
1, 3, 5, 7, 9,
11, 13, 15
P1.0 - P1.7. General purpose I/O Port 1
17
RST - Active high reset input. A logic 1 applied to this pin will activate a reset state.
This pin is pulled down internally so this pin can be left unconnected if not used. An
RC power-on reset circuit is not needed and is not recommended.
19
P3.0 RXD. General purpose I/O port pin 3.0. Also serves as the receive signal for the
on board UART. This pin should not be connected directly to a PC COM port.
21
P3.1 TXD. General purpose I/O port pin 3.1. Also serves as the transmit signal for the
on board UART. This pin should not be connected directly to a PC COM port.
23
P3.2 INT0 . General purpose I/O port pin 3.2. Also serves as the active low External
Interrupt 0.
25
P3.3 INT1 . General purpose I/O port pin 3.3. Also serves as the active low External
Interrupt 1.
27
P3.4 T0. General purpose I/O port pin 3.4. Also serves as the Timer 0 input.
29
P3.5 T1. General purpose I/O port pin 3.5. Also serves as the Timer 1 input.
31
P3.6 WR . General purpose I/O port pin. Also serves as the write strobe for Expanded
bus operation.
33
P3.7 RD . General purpose I/O port pin. Also serves as the read strobe for Expanded
bus operation.
35, 37
XTAL2, XTAL1. Used to connect an external crystal to the internal oscillator.
XTAL1 is the input to an inverting amplifier and XTAL2 is the output.
39
GND - Logic ground.
26, 28, 30, 32,
34, 36, 38, 40
P2.7-P2.0. General purpose I/O Port 2. Also serves as the MSB of the Expanded
Address bus.
24
PSEN
- Program Store Enable. This active low signal is used to enable an external
program memory when using the Expanded bus. It is normally an output and should
be unconnected if not used. PSEN also is used to invoke the Bootstrap Loader. At this
time, PSEN will be pulled down externally. This should only be done once the
DS2250(T) is already in a reset state. The device that pulls down should be open-drain
since it must not interfere with PSEN under normal operation.
22
ALE - Address Latch Enable. Used to de-multiplex the multiplexed Expanded
Address/Data bus on Port 0. This pin is normally connected to the clock input on a
’373 type transparent latch. When using a parallel programmer, this pin also assumes
the PROG function for programming pulses.
20
EA
- External Access. This pin forces the DS2250(T) to behave like an 8031. No
internal memory (or clock) will be available when this pin is at a logic low. Since this
pin is pulled down internally, it should be connected to +5V to use NV RAM. In a
parallel programmer, this pin also serves as VPP for super voltage pulses.
4, 6, 8, 10, 12,
14, 16, 18
P0.0-P0.7. General purpose I/O Port 0. This port is open-drain and can not drive a
logic 1. It requires external pullups. Port 0 is also the multiplexed Expanded
Address/Data bus. When used in this mode, it does not require pullups.
2
VCC + - 5 volts.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC12C672/JW | IC MCU EPROM 2KX14 A/D 8CDIP |
| PIC17C44/JW | IC MCU EPROM 8KX16 PWM 40CDIP |
| PIC17C43/JW | IC MCU EPROM 4KX16 PWM 40CDIP |
| PIC17C42A/JW | IC MCU EPROM 2KX16 PWM 40CDIP |
| PIC16LC74A-04I/P | IC MCU OTP 4KX14 A/D PWM 40DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2250-32-16+ | 功能描述:模塊化系統 - SOM Soft MCU Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| DS2250-64-08 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| DS2250-64-12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller |
| DS2250-64-16 | 功能描述:模塊化系統 - SOM Soft MCU Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
| DS2250-64-16# | 功能描述:模塊化系統 - SOM Soft MCU Module RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in |
發布緊急采購，3分鐘左右您將得到回復。