(-40°C to +85°C, VPUP = 2.5V to 6.0V, V
參數資料
型號: DS2415P+T&R
廠商: Maxim Integrated Products
文件頁數: 6/14頁
文件大?。?/td> 0K
描述: IC TIME CHIP 1-WIRE 6-TSOC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 4,000
類型: 二進制計數器
特點: 唯一 ID
時間格式: 二進制
數據格式: 二進制
接口: 1 線 串行
電源電壓: 2.5 V ~ 5.5 V
電壓 - 電源,電池: 2.5 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 6-LSOJ
供應商設備封裝: 6-TSOC
包裝: 帶卷 (TR)
DS2415
14 of 14
AC ELECTRICAL CHARACTERISTICS
(-40°C to +85°C, VPUP = 2.5V to 6.0V, VBAT = 2.5V to 5.5V)
PARAMETER
SYMBOL MIN
TYP
MAX
UNITS NOTES
Time Slot
tSLOT
60
120
ms
Write 1 Low Time
tLOW1
115
ms
14
Write 0 Low Time
tLOW0
60
120
ms
Read Low Time
tLOWR
115
ms
14
Read Data Valid
tRDV
15
ms
13
Release Time
tRELEASE
015
45
ms
Read Data Setup
tSU
1
ms
6
Recovery Time
tREC
1
ms
Reset Time High
tRSTH
480
ms
5
Reset Time Low
tRSTL
480
960
ms
8
Presence Detect High
tPDH
15
60
ms
Presence Detect Low
tPDL
60
240
ms
NOTES:
1. All voltages are referenced to ground.
2. Measured with outputs open.
3. VPUP = external pullup voltage.
4. Input load is to ground.
5. An additional reset or communication sequence cannot begin until the reset high time has expired.
6. Read data setup time refers to the time the bus master must pull the I/O line low to read a bit. Data is
guaranteed to be valid within 1
ms of this falling edge.
7. Under certain low voltage conditions VIL1MAX may have to be reduced to as much as 0.5V to always
guarantee a Presence Pulse.
8. The reset low time (tRSTL) should be restricted to a maximum of 960
ms, to allow interrupt signaling,
otherwise, it could mask or conceal interrupt pulses.
9. When VBAT ramps up, the oscillator is always off.
10. At VBAT = 3V
± 10%
11. At VBAT = 5V
± 10%
12. VIH1 has to be VBAT -0.3V or higher.
13. The optimal sampling point for the master is as close as possible to the end time of the 15s tRDV
period without exceeding tRDV. For the case of a Read-One Time Slot, this maximizes the amount of
time for the pull-up resistor to recover to a high level. For a Read-Zero Time Slot, it ensures that a
read will occur before the fastest 1-Wire device(s) release the line.
14. The duration of the low pulse sent by the master should be a minimum of 1s with a maximum value
as short as possible to allow time for the pull-up resistor to recover the line to a high level before the
1-Wire device samples in the case of a Write-One Time or before the master samples in the case of a
Read-One Time.
相關PDF資料
PDF描述
DS2417X/T&R IC TIMECHIP W/INTRPT 1WIRE CSP
DS26502LN+ IC T1/E1/J1 64KCC ELEMENT 64LQFP
DS26503LN+ IC T1/E1/J1 BITS ELEMENT 64-LQFP
DS3105LN+ IC TIMING LINE CARD 64-LQFP
DS3106LN+ IC TIMING LINE CARD 64-LQFP
相關代理商/技術參數
參數描述
DS2415P-W 功能描述:實時時鐘 RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
DS2415V 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:1-Wire Time Chip
DS2415X 功能描述:IC TIME CHIP 1-WIRE CSP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 實時時鐘 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 類型:時鐘/日歷 特點:警報器,閏年,SRAM 存儲容量:- 時間格式:HH:MM:SS(12/24 小時) 數據格式:YY-MM-DD-dd 接口:SPI 電源電壓:2 V ~ 5.5 V 電壓 - 電源,電池:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-WDFN 裸露焊盤 供應商設備封裝:8-TDFN EP 包裝:管件
DS2416FP00K 制造商:Thomas & Betts 功能描述:200A,CON,3P4W,MG,416,3P208V,CC
DS2416FR000 制造商:Thomas & Betts 功能描述:200A,REC,3P4W,MG,416,3P208V,SC