- 您現在的位置：買賣IC網 > PDF目錄376969 > DS2437S IC-SM-BATT MONITOR PDF資料下載
參數資料
| 型號： | DS2437S |
| 英文描述： | IC-SM-BATT MONITOR |
| 中文描述： | 集成電路釤棉絮顯示器 |
| 文件頁數： | 24/31頁 |
| 文件大?。?/td> | 1215K |
| 代理商： | DS2437S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
DS2437
24 of 31
I/O SIGNALING
The DS2437 requires strict protocols to insure data integrity. The protocol consists of several types of
signaling on one line: reset pulse, presence pulse, write 0, write 1, read 0, and read 1. All of these signals,
with the exception of the presence pulse, are initiated by the bus master.
The initialization sequence required to begin any communication with the DS2437 is shown in Figure 9.
A reset pulse followed by a presence pulse indicates the DS2437 is ready to send or receive data given the
correct ROM command and memory function command.
The bus master transmits (Tx) a reset pulse (a low signal for a minimum of 480
μ
s). The bus master then
releases the line and goes into a receive mode (Rx). The 1-Wire bus is pulled to a high state via the
5 k
=
pullup resistor. After detecting the rising edge on the I/O pin, the DS2437 waits 15-60
μ
s and then
transmits the presence pulse (a low signal for 60-240
μ
s). DS2437 data is read and written through the
use of time slots to manipulate bits and a command word to specify the transaction.
INITIALIZATION PROCEDURE "RESET AND PRESENCE PULSES"
Figure 9
Write Time Slots
A write time slot is initiated when the host pulls the data line from a high (inactive) logic level to a low
logic level. There are two types of write time slots: Write 1 time slots and Write 0 time slots. All write
time slots must be a minimum of 60
μ
s in duration with a minimum of a 1
μ
s recovery time between
individual write cycles.
The DS2437 samples the I/O line in a window of 15
μ
s to 60
μ
s after the I/O line falls. If the line is high,
a Write 1 occurs. If the line is low, a Write 0 Occurs (See Figure 10).
For the host to generate a Write 1 time slot, the data line must be pulled to a logic low level and then
released, allowing the data line to pull up to a high level within 15 microseconds after the start of the
write time slot.
For the host to generate a Write 0 time slot, the data line must be pulled to a logic low level and remain
low for the duration of the write time slot.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2437 | Smart Battery Monitor |
| DS2438 | Smart Battery Monitor |
| DS2438Z | Smart Battery Monitor |
| DS2442 | Battery Management |
| DS2501 | 1A VERY LOW DROPOUT VOLTAGE REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2437S/T&R | 制造商:Maxim Integrated Products 功能描述:SMART BATTERY MONITOR 16SSOP T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MONITOR SMART BATTERY 16-SSOP |
| DS2437S/T&R/ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS2437S/T&R | 功能描述:IC MONITOR SMART BATTERY 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| DS2437S-3 | 功能描述:IC MONITOR SMART BATTERY 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| DS2437S-3/T&R | 制造商:Maxim Integrated Products 功能描述:IC MONITOR SMART BATTERY 16-SSOP |
發布緊急采購，3分鐘左右您將得到回復。