- 您現在的位置：買賣IC網 > PDF目錄1915 > DS2482X-101+T (Maxim Integrated Products)IC MASTER I2C-1WIRE 1CH 9-WLP PDF資料下載
參數資料
| 型號： | DS2482X-101+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/24頁 |
| 文件大小： | 0K |
| 描述： | IC MASTER I2C-1WIRE 1CH 9-WLP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 控制器類型： | I²C 總線控制器 |
| 接口： | I²C |
| 電源電壓： | 2.9 V ~ 5.5 V |
| 電流 - 電源： | 750µA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 9-WFBGA，WLBGA |
| 供應商設備封裝： | 9-WLP |
| 包裝： | 帶卷 (TR) |
DS2482-101
Single-Channel 1-Wire Master with Sleep Mode
______________________________________________________________________________________
15
I2C Interface
General Characteristics
The I2C bus uses a data line (SDA) plus a clock signal
(SCL) for communication. Both SDA and SCL are bidi-
rectional lines, connected to a positive supply voltage
through a pullup resistor. When there is no communica-
tion, both lines are high. The output stages of devices
connected to the bus must have an open drain or open
collector to perform the wired-AND function. Data on
the I2C bus can be transferred at rates of up to
100kbps in standard mode and up to 400kbps in fast
mode. The DS2482-101 works in both modes.
A device that sends data on the bus is defined as a
transmitter, and a device receiving data is defined as a
receiver. The device that controls the communication is
called a master. The devices that are controlled by the
master are slaves. To be individually accessed, each
device must have a slave address that does not conflict
with other devices on the bus.
Data transfers can be initiated only when the bus is not
busy. The master generates the serial clock (SCL), con-
trols the bus access, generates the START and STOP
conditions, and determines the number of data bytes
transferred between START and STOP (Figure 7). Data
is transferred in bytes with the most significant bit being
transmitted first. After each byte follows an acknowledge
bit to allow synchronization between master and slave.
Slave Address
The slave address to which the DS2482-101 responds
is shown in Figure 8. The logic state at the address pin
AD0 determines the value of the address bit A0. The
address pin allows the device to respond to one of two
possible slave addresses. The slave address is part of
the slave address/control byte. The last bit of the slave
address/control byte (R/W) defines the data direction.
When set to 0, subsequent data flows from master to
slave (write access); when set to 1, data flows from
slave to master (read access).
SDA
SCL
IDLE
1–7
8
9
1–7
8
9
1–7
8
9
START
CONDITION
STOP CONDITION
REPEATED START
SLAVE
ADDRESS
R/W
ACK
DATA
ACK/
NACK
DATA
MSB FIRST
MSB
LSB
MSB
LSB
REPEATED IF MORE BYTES
ARE TRANSFERRED
Figure 7. I2C Protocol Overview
Figure 8. DS2482-101 Slave Address
0
A6
MSB
0
A5
1
A4
1
A3
7-BIT SLAVE ADDRESS
0
A2
0
A1
AD0
A0
R/W
DETERMINES
READ OR WRITE
AD0
PIN STATE
相關PDF資料 |
PDF描述 |
|---|---|
| DS2483Q+T | IC I2C TO 1WIRE BRIDGE 8TDFN |
| DS2490Y | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| DS26303LN-75+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
| DS26324GNA2+ | IC INTERFACE LINE 16CH 256-CSBGA |
| DS26334GN+ | IC INTERFACE LINE 16CH 256-CSBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2483 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Single-Channel 1-Wire Master with Adjustable Timing and Sleep Mode |
| DS2483Q+T | 功能描述:I2C 接口集成電路 Single-Channel 1-Wire Master RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| DS2483Q+U | 功能描述:I2C 接口集成電路 SINGLE-CH 1-WIRE MASTER RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| DS2483R+T | 功能描述:I2C 接口集成電路 Single-Channel 1-Wire Master RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| DS2483R+U | 功能描述:接口 - 專用 SINGLE-CH 1-WIRE MASTER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。