- 您現在的位置：買賣IC網 > PDF目錄1915 > DS2483Q+T (Maxim Integrated Products)IC I2C TO 1WIRE BRIDGE 8TDFN PDF資料下載
參數資料
| 型號： | DS2483Q+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/29頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC I2C TO 1WIRE BRIDGE 8TDFN |
| 產品培訓模塊： | Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 系列： | * |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
10
Maxim Integrated
DS2483
Single-Channel 1-Wire Master
with Adjustable Timing and Sleep Mode
Port Configuration Register
The Port Configuration register allows verifying the set-
tings for the 1-Wire port (Table 4). The Adjust 1-Wire
Port command positions the read pointer to the Port
Configuration register for the host processor to read
with minimal protocol overhead. When reading the Port
Configuration register, the parameter values are reported
in this sequence:
Parameter 000 (tRSTL) standard speed, overdrive speed
Parameter 001 (tMSP) standard speed, overdrive speed
Parameter 010 (tW0L) standard speed, overdrive speed
Parameter 011 (tREC0)
Parameter 100 (RWPU)
If one continues reading, the parameter number rolls
over to 000 and one receives the same data again.
Note that the upper 4 bits read from the port configura-
tion register are always 0. See Table 7 for the conversion
between parameter value code and actual parameter
value.
Function Commands
The DS2483 understands nine function commands that
fall into four categories: device control, I2C communi-
cation, 1-Wire setup, and 1-Wire communication. The
feedback path to the host is controlled by a read pointer,
which is set automatically by each function command
for the host to efficiently access relevant information.
The host processor sends these commands and appli-
cable parameters as strings of 1 or 2 bytes using the
I2C interface. The I2C protocol requires that each byte
be acknowledged by the receiving party to confirm
acceptance or not be acknowledged to indicate an error
condition (invalid code or parameter) or to end the com-
munication. See the I2C Interface section for details of
the I2C protocol including acknowledge.
The function commands are as follows:
1) Device Reset
2) Set Read Pointer
3) Write Device Configuration
4) Adjust 1-Wire Port
5) 1-Wire Reset
6) 1-Wire Single Bit
7) 1-Wire Write Byte
8) 1-Wire Read Byte
9) 1-Wire Triplet
Table 4. Port Configuration Register Bit Assignment
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
0
VAL3
VAL2
VAL1
VAL0
BITS 3:0
VAL[3:0]: Parameter Value Code
See Table 7 for the conversion between binary code and parameter value.
相關PDF資料 |
PDF描述 |
|---|---|
| DS2490Y | IC BRIDGE CLIP USB TO 1-W 24SOIC |
| DS26303LN-75+A3 | IC LIU E1/T1/J1 3.3V 144-ELQFP |
| DS26324GNA2+ | IC INTERFACE LINE 16CH 256-CSBGA |
| DS26334GN+ | IC INTERFACE LINE 16CH 256-CSBGA |
| DS26401N+ | IC OCTAL FRAMER T1/E1/J1 256-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS2483R+T | 功能描述:I2C 接口集成電路 Single-Channel 1-Wire Master RoHS:否 制造商:NXP Semiconductors 電源電壓-最大:5.5 V 電源電壓-最小:2.3 V 最大工作頻率:400 KHz 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-16 |
| DS2483R+U | 功能描述:接口 - 專用 SINGLE-CH 1-WIRE MASTER RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS2484Q+T | 制造商:Maxim Integrated Products 功能描述: |
| DS2484R+T | 制造商:Maxim Integrated Products 功能描述: |
| DS2490 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:USB to 1-Wire Bridge Chip |
發布緊急采購，3分鐘左右您將得到回復。