- 您現在的位置：買賣IC網 > PDF目錄16259 > DS26334DK (Maxim Integrated Products)KIT DESIGN FOR DS26334 PDF資料下載
參數資料
| 型號： | DS26334DK |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 106/121頁 |
| 文件大?。?/td> | 0K |
| 描述： | KIT DESIGN FOR DS26334 |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 設計資源： | DS26334DK Gerber Files |
| 標準包裝： | 1 |
| 主要目的： | 電信，線路接口單元（LIU） |
| 已用 IC / 零件： | DS26334 |
| 已供物品： | 板，線纜，電源 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁當前第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁
DS26334 3.3V, 16-Channel, E1/T1/J1 Short/Long-Haul Line Interface Unit
85 of 121
6.1.4
BERT Registers
Register Name:
BCR
Register Description:
BERT Control Register
Register Address (LIUs 1–8):
00h
Register Address (LIUs 9–16):
20h
Bit #
7
6
5
4
3
2
1
0
Name
PMUM
LPMU
RNPL
RPIC
MPR
APRD
TNPL
TPIC
Default
0
Bit 7: Performance Monitoring Update Mode (PMUM). When 0, a performance monitoring update is initiated by
the LPMU register bit. When 1, a performance monitoring update is initiated by the receive performance monitoring
update signal (RPMU). Note: If RPMU or LPMU is one, changing the state of this bit may cause a performance
monitoring update to occur.
Bit 6: Local Performance Monitoring Update (LPMU). This bit causes a performance monitoring update to be
initiated if local performance monitoring update is enabled (PMUM = 0). A 0-to-1 transition causes the performance
monitoring registers to be updated with the latest data, and the counters reset (0 or 1). For a second performance
monitoring update to be initiated, this bit must be set to 0, and back to 1. If LPMU goes low before the PMS bit
goes high, an update might not be performed. This bit has no affect when PMUM = 1.
Bit 5: Receive New Pattern Load (RNPL). A 0-to-1 transition of this bit will cause the programmed test pattern
(QRSS, PTS, PLF[4:0], PTF[4:0], and BSP[31:0]) to be loaded in to the receive pattern generator. This bit must be
changed to zero and back to one for another pattern to be loaded. Loading a new pattern will forces the receive
pattern generator out of the “Sync” state which causes a resynchronization to be initiated. Note: QRSS, PTS,
PLF[4:0], PTF[4:0], and BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four RXCK
clock cycles after this bit transitions from 0 to 1.
Bit 4: Receive Pattern Inversion Control (RPIC). When 0, the receive incoming data stream is not altered. When
1, the receive incoming data stream is inverted.
Bit 3: Manual Pattern Resynchronization (MPR). A zero to one transition of this bit will cause the receive pattern
generator to resynchronize to the incoming pattern. This bit must be changed to zero and back to one for another
resynchronization to be initiated. Note: A manual resynchronization forces the receive pattern generator out of the
“Sync” state.
Bit 2: Automatic Pattern Resynchronization Disable (APRD). When 0, the receive pattern generator will
automatically resynchronize to the incoming pattern if six or more times during the current 64-bit window the
incoming data stream bit and the receive pattern generator output bit did not match. When 1, the receive pattern
generator will not automatically resynchronize to the incoming pattern. Note: Automatic synchronization is
prevented by not allowing the receive pattern generator to automatically exit the “Sync” state.
Bit 1: Transmit New Pattern Load (TNPL). A 0-to-1 transition of this bit will cause the programmed test pattern
(QRSS, PTS, PLF[4:0], PTF[4:0], and BSP[31:0]) to be loaded in to the transmit pattern generator. This bit must be
changed to zero and back to one for another pattern to be loaded. Note: QRSS, PTS, PLF[4:0], PTF[4:0], and
BSP[31:0] must not change from the time this bit transitions from 0 to 1 until four TXCK clock cycles after this bit
transitions from 0 to 1.
Bit 0: Transmit Pattern Inversion Control (TPIC). When 0, the transmit outgoing data stream is not altered.
When 1, the transmit outgoing data stream is inverted.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-JWH-EY-S | CONVERTER MOD DC/DC 52V 50W |
| GCC19DREN | CONN EDGECARD 38POS .100 EYELET |
| GBM36DSEH-S243 | CONN EDGECARD 72POS .156 EYELET |
| GCC19DREH | CONN EDGECARD 38POS .100 EYELET |
| GCC20DCST | CONN EDGECARD 40POS DIP .100 SLD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS26334G | 功能描述:電信集成電路 3.3V E1/T1/J1 16Ch Short/Long Haul LIU RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26334G+ | 功能描述:電信集成電路 3.3V E1/T1/J1 16Ch Short/Long Haul LIU RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26334GA2 | 功能描述:電信集成電路 RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26334GA2+ | 功能描述:電信集成電路 RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
| DS26334GA3 | 功能描述:電信集成電路 3.3V E1/T1/J1 16Ch Short/Long Haul LIU RoHS:否 制造商:STMicroelectronics 類型:Telecom IC - Various 工作電源電壓:4.75 V to 5.25 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PQFP-100 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。