參數資料
型號: DS2890P-000+
廠商: Maxim Integrated Products
文件頁數: 25/27頁
文件大?。?/td> 0K
描述: IC POT DIGITAL 1-WIRE 100K 6TSOC
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 120
接片: 256
電阻(歐姆): 100k
電路數: 1
溫度系數: 標準值 800 ppm/°C
存儲器類型: 易失
接口: 1 線 串行
電源電壓: 2.8 V ~ 6 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 6-LSOJ
供應商設備封裝: 6-TSOC
包裝: 管件
DS2890
7 of 27
POWER and CONFIGURATION CONSIDERATIONS
1-Wire devices can typically derive operating power entirely from the 1-Wire bus by storing energy on an
internal capacitor during periods of time when the 1-Wire bus is in a high state. During bus low times the
device continues to operate from the energy stored on the internal capacitor; the capacitor is then
recharged when the bus returns to a high state. This technique of operating entirely from the 1-Wire bus
by powering from energy stored on an internal capacitor during bus low times in known as “parasite
powered” operation.
Special consideration is required with the DS2890 in that it supports two power
configurations and two related digital resistor modes: Potentiometer Configuration and Variable Resistor
Configuration. The Potentiometer Configuration requires the presence of a VDD power source to supply
the power needs of the device charge pump which must be turned on to support a terminal-to-terminal
wiper output range. The Variable Resistor configuration is supported with or without a VDD source or
enabled charge pump although resistance range, as described below, is influenced by the charge pump
state.
POTENTIOMETER CONFIGURATION
To configure and operate the DS2890 as a potentiometer as shown in Figure 5 requires the TSOC, a VDD
power source, and the device charge pump turned on (Control Register, bit CPC=1). The charge pump
must be enabled to support RL to RH terminal voltage swings at the WIPER output and as described
previously, a VDD supply must be provided to support the power requirements of the charge pump.
Figure 5. Potentiometer Configuration
RH
WIPER
RL
VDD
1-WIRE
GND
2.8V to 6.0V
Bus
Master
VARIABLE RESISTOR CONFIGURATION
The Variable Resistor configuration as shown in Figure 6 is supported by all package types with or
without an external VDD supply. As described previously, without a VDD source the charge pump must
be disabled.
Figure 6. Variable Resistor Configurations
(TO92 Package)
RH
WIPER
RL
VDD
1-WIRE
GND
2.8V to 6.0V
or
No Connect
2.8V to 6.0V
Bus
Master
RH
1-WIRE
GND
2.8V to 6.0V
Bus
Master
相關PDF資料
PDF描述
DS1869S-100+T&R IC RHEOSTAT DALLST 3V 100K 8SOIC
VI-B5Z-MX-F2 CONVERTER MOD DC/DC 2V 30W
VI-B5Z-MX-F1 CONVERTER MOD DC/DC 2V 30W
VI-B5Y-MX-F4 CONVERTER MOD DC/DC 3.3V 49.5W
VI-B5Y-MW-F4 CONVERTER MOD DC/DC 3.3V 66W
相關代理商/技術參數
參數描述
DS2890P-000+ 功能描述:IC POT DIGITAL 1-WIRE 100K 6TSOC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻(歐姆):50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)
DS2890P-000+T&R 制造商:Maxim Integrated Products 功能描述:IC POT DIGITAL 1-WIRE 100K 6TSOC
DS2890P-000+T&R 功能描述:IC POT DIGITAL 1-WIRE 100K 6TSOC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻(歐姆):50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)
DS2890T 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:1-Wire Digital Potentiometer
DS2890T-000 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel