- 您現在的位置：買賣IC網 > PDF目錄9560 > DS3150T (Maxim Integrated Products)IC LIU T3/E3/STS-1 48-TQFP PDF資料下載
參數資料
| 型號： | DS3150T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T3/E3/STS-1 48-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS |
| 產品變化通告： | Product Discontinuation 20/Feb/2012 |
| 標準包裝： | 250 |
| 類型： | 線路接口裝置（LIU） |
| 驅動器/接收器數： | 1/1 |
| 規程： | DS3 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
DS3150
19 of 28
NAME
TYPE
FUNCTION
TDS1/
OFSEL
I3
(Note 2)
Transmit Data Select Bit 1/Oscillator Frequency Select. If EFE = 1, TDS1, TDS0
and TESS select the source of the transmit data (Table 2-B). If EFE = 0, TDS1 is
ignored. If MCLK is wired low, TDS1 is internally pulled low, and a resistor connected
between this pin (OFSEL) and ground determines the frequency of an internal
oscillator. The following resistor values should be used for specific applications:
E3: 6.81k
W, ±2%
DS3: 5.23k
W, ±2%
STS-1: 4.53k
W, ±2%
When switching among DS3, E3, and STS-1 modes, do not allow OFSEL to float.
Instead, hardwire the highest resistor value and switch in series or parallel resistors as
needed. Example: For a DS3/E3 application, hardwire 5.23k for DS3 and switch in
series 1.58k to get 6.81k for E3.
TESS
I3
(Note 2)
T3/E3/STS-1 Select. TESS determines the mode of operation for the device.
0 = E3
1 = T3 (DS3)
Float = STS-1
TNEG
I3
(Note 2)
Transmit Negative Data. When the B3ZS/HDB3 encoder is disabled (
ZCSE = 1),
TNEG should be driven high to transmit a negative AMI pulse. When the B3ZS/HDB3
encoder is enabled (
ZCSE = 0), the NRZ data stream should be applied to TNRZ, while
TNEG is ignored and can be wired either high or low. TNEG is sampled either on the
falling edge of TCLK (ICE = 1 or Float) or the rising edge of TCLK (ICE = 0).
TPOS/
TNRZ
I
Transmit Positive Data. When the B3ZS/HDB3 encoder is disabled (
ZCSE = 1),
TPOS should be driven high to transmit a positive AMI pulse. When the B3ZS/HDB3
encoder is enabled (
ZCSE = 0), the NRZ data stream should be applied to TNRZ.
TPOS/TNRZ is sampled either on the falling edge of TCLK (ICE = 1 or Float) or the
rising edge of TCLK (ICE = 0).
TTS
I3
(Note 2)
Transmit Tri-State.
TTS determines whether the TX+ and TX- analog outputs are tri-
stated or active. This input also controls the jitter attenuator (Table 2-C).
0 = tri-state the transmit output driver, disable the jitter attenuator in the transmit path
1 = enable the transmit output driver, disable the jitter attenuator in the transmit path
Float = enable the transmit output driver, enable the jitter attenuator in the transmit path
TX+,
TX-
O3
(Note 3)
Transmit Analog Outputs. These differential AMI outputs are coupled to the
outbound 75
W coaxial cable through a 2:1 step-down transformer (Figure 1-2). These
outputs can be tri-stated using the
TTS input pin.
VDD
P
Positive Supply. 3.3V
±5%. All VDD pins should be wired together.
VSS
P
Ground Reference. All VSS pins should be wired together.
ZCSE
I
Active-Low Zero Code Suppression Enable.
ZCSE has an internal 80k
W pullup to
VDD.
0 = B3ZS/HDB3 encoder/decoder enabled (NRZ interface enabled)
1 = B3ZS/HDB3 encoder/decoder disabled (bipolar interface enabled)
Note 1:
Pin type I = input pin. Pin type O = output pin. Pin type P = power-supply pin.
Note 2:
Pin type I3 is an input capable of detecting three states: high, low, and float. All I3 inputs have an internal 13k
W pullup to
approximately 1.5V. The voltage range of the float state is approximately 1.2V to 1.9V. If the function of the float state of an I3 pin
is not defined in Table 2-A, then the float state is used for factory test only.
Note 3:
Pin type O3 is an output that is tri-state capable.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B6H-MY-S | CONVERTER MOD DC/DC 52V 50W |
| VI-25F-MX-F4 | CONVERTER MOD DC/DC 72V 75W |
| VI-26X-CU-B1 | CONVERTER MOD DC/DC 5.2V 200W |
| VE-B6F-MY-S | CONVERTER MOD DC/DC 72V 50W |
| VI-26W-CU-B1 | CONVERTER MOD DC/DC 5.5V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3150T+ | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TC1 | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TC1+ | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TN | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS3150TN+ | 功能描述:網絡控制器與處理器 IC 3.3V DS3/E3/STS-1 Line Interface Unit RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。