- 您現在的位置：買賣IC網 > PDF目錄1916 > DS33Z11+UNUSED (Maxim Integrated Products)IC ETHERNET MAPPER 169-CSBGA PDF資料下載
參數資料
| 型號： | DS33Z11+UNUSED |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 31/34頁 |
| 文件大小： | 0K |
| 描述： | IC ETHERNET MAPPER 169-CSBGA |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 7 |
| 應用： | 數據傳輸 |
| 接口： | SPI/并聯 |
| 電源電壓： | 1.8V, 3.3V |
| 封裝/外殼： | 169-LBGA，CSPBGA |
| 供應商設備封裝： | 169-CSBGA（14x14） |
| 包裝： | 托盤 |
| 安裝類型： | 表面貼裝 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁
_______________________________________________________________________________
DS33Z11DK
Rev: 080508
6 of 34
4.3
Quick Setup #3 (DS2155 T1E1)
Install jumpers to place the serial interface in T1E1 mode as shown in Figure 1.
Complete the hardware configuration and one of the basic DS33Z11 configurations as previously described.
Launch ChipView.exe (or use existing session if its already open) and select Register View. When prompted
for a definition file, pick the file named DS33Z11.def. After the definition file loads, go to the File menu and
select File→Memory Config File→Load .MFG file. When prompted, select the file named basic_config.mfg.
Load the definition file for the DS2155 by going to the file menu and selecting File→Definition Config File and
select the definition file named DS2155.def. After the definition file loads, go to the File menu and select
File
→Reg Ini File→Load Ini File. When prompted, pick the file named e1_gapclk_crc4_hdb3_nocas.ini.
Place a loopback connector at the DS2155 network side; RLOS LED DS35 should go out.
At this point any packets sent to the DS33Z11 are echoed back. Incoming packets (i.e., ping) should cause the
ACT LED to blink.
4.4
Quick Setup #4 (DS3170 T3E3)
Install jumpers to place the serial interface in T3E3 mode as shown in Figure 1.
Complete the hardware configuration and one of the basic DS33Z11 configurations as previously described.
Launch ChipView.exe (or use existing session if its already open) and select Register View. When prompted
for a definition file, pick the file named DS33Z11.def. After the definition file loads, go to the File menu and
select File→Memory Config File→Load .MFG file. When prompted, select the file named basic_config.mfg.
Load the definition file for the DS3170 by going to the file menu and selecting File→Definition Config File and
select the definition file named ds3170_global.def. After the definition file loads, go to the File menu and
select
File→Memory
Config
File→Load
.MFG
file.
When
prompted,
select
the
file
named
70_t3_sct_needscoaxlb.mfg.
Place a loopback connector at the DS3170 network side.
At this point any packets sent to the DS33Z11 are echoed back. Incoming packets (i.e., ping) should cause the
ACT LED to blink.
5. Monitor and Capture Ethernet Traffic
Although ping is mentioned, it is *not* recommended. The ping command goes through the computer’s TCPIP
stack, and sometimes will not be sent out the PC’s network connector (i.e., if the PCs’ ARP cache is out of
date). Additionally ping requires two PCs, as a PC with only one adapter can not ping itself (a local ping gets
sent to ‘local host’ instead of out the connector). With that said, ping is still a valuable test once the prototyping
stage is complete.
Generation and capture of arbitrary (raw) packets can be easily accomplished using CommView. A time-limited
demo is available at the website www.tamos.com/products/commview.
Wireshark is an excellent (and free) packet capture utility. Download is available at www.wireshark.org.
Adding additional Ethernet ports to a PC is rather simple when a USB-to-Ethernet adapter is used. This allows
for end-to-end testing using a single PC. When using two adapters the PC will have a different IP address for
each adapter. Test equipment will allow selection of either adapter. Operating system based network traffic will
be sent out the default adapter, usually this is the adapter that has recently had connection to a live network.
相關PDF資料 |
PDF描述 |
|---|---|
| DS33Z44+ | IC MAPPER ETHERNET 256CSBGA |
| DS33ZH11+ | IC MAPPER ETHERNET 100CSBGA |
| DS34C87TN/NOPB | IC LINE DRIVER QUAD CMOS 16-DIP |
| DS34LV87TMX/NOPB | IC LINE DVR QUAD CMOS DIF 16SOIC |
| DS34S132GN+ | IC TDM OVER PACKET 676-BGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS33Z41 | 功能描述:網絡控制器與處理器 IC Quad IMUX Ethernet Mapper RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS33Z41DK | 功能描述:以太網開發工具 DS33Z41 Dev Kit RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| DS33Z44 | 功能描述:網絡控制器與處理器 IC Quad Ethernet Mapper RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS33Z44+ | 功能描述:網絡控制器與處理器 IC Quad Ethernet Mapper RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray |
| DS33Z44DK | 功能描述:以太網開發工具 DS33Z44 Dev Kit RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。