參數資料
型號： DS33Z44+
廠商： Maxim Integrated Products
文件頁數： 5/59頁
文件大?。?/td> 0K
描述： IC MAPPER ETHERNET 256CSBGA
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 40
應用： 數據傳輸
接口： 串行
電源電壓： 1.8V，2.5V，3.3V
封裝/外殼： 256-LBGA，CSBGA
供應商設備封裝： 256-CSBGA（17x17）
包裝： 托盤
安裝類型： 表面貼裝
DS33Z44DK
13 of 59
CONFIGURATION SWITCHES AND JUMPERS
The DS33Z44DK has several configuration switches, banana plugs, oscillators, and jumpers. Table 2 provides a
description of these signals, given in order of appearance on the PC board (going from left to right, top to bottom).
Table 2. Main Board PC Board Configuration
BASIC SETTING
SILKSCREEN
REFERENCE
FUNCTION
SW MODE
HW MODE
DESCRIPTION
J25.9 + J25.10
Reserved
Not Installed
—
This jumper is not for use with the
DS33Z44 design kit. Pin J25.10 has
been removed to prevent accidental
installation.
J25.7 + J25.8
Enable device driver
User decision
—
When installed the device driver will
configure the DS33Z44 and the
Transceiver during power-up.
J25.5 + J25.6
Enable callbacks
User decision
—
When installed the driver will
respond to interrupts.
GROUND
(banana plug)
Power supply ground
—
System Ground. Always connected
to power supply.
VDD 3.3V
(banana plug)
Power supply VDD
—
System VDD. Always connected to
power supply.
OnCe
BDM
—
Debug connector for processor
DCEDTES
(3pos switch)
DS33Z44 mode pin;
DTE/DCE selection
Low
Low for DTE
RMIIMII
(3pos switch)
DS33Z44 mode pin
Low
High for RMII, low for MII
CKPHA
(3pos switch)
DS33Z44 mode pin
Low
SPI EEPROM hardware mode
configuration switch
MODEC0
(3pos switch)
DS33Z44 mode pin
High
Low
Software mode selected
MODEC1
(3pos switch)
DS33Z44 mode pin
Low
Software mode selected
HWMODE
(3pos switch)
DS33Z44 mode pin
Low
Hardware/software mode (software
mode selected)
SCANMO
(3pos switch)
DS33Z44 mode pin
Low
Set low for normal operation
SCANTRI
(3pos switch)
DS33Z44 mode pin
Low
Set low for normal operation
….testpoints….
DS33Z44 testpoints
—
Processor bus, JTAG and LAN side
testpoints for Zchip
Z-RESET (button) DS33Z44 reset
—
System reset
A2, A1, A0
(3pos switches)
DS33Z44/SPI pins
Mid position
Address pin/EEPROM config switch.
Set to mid position to allow
connection to processor.
SDRAM CLOCK
DS33Z44 SDRAM
clock
Installed
100MHz oscillator to drive SDRAM
clock
MII CLOCK
PHY MII clock
Installed
25MHz oscillator to drive SDRAM
clock
spi_cs, spi_ck,
spi_miso,
spi_mosi
—
SPI signals (for EEPROM memory)
….testpoints…..
DS33Z44 testpoints
—
DS33Z44 serial port testpoints
AFCS
(1 per port)
DS33Z44 mode pin
HW mode only
High
Set high to enable auto flow control.
相關PDF資料
PDF描述
DS33ZH11+ IC MAPPER ETHERNET 100CSBGA
DS34C87TN/NOPB IC LINE DRIVER QUAD CMOS 16-DIP
DS34LV87TMX/NOPB IC LINE DVR QUAD CMOS DIF 16SOIC
DS34S132GN+ IC TDM OVER PACKET 676-BGA
DS34T102GN+ IC TDM OVER PACKET 484TEBGA
相關代理商/技術參數
參數描述
DS33Z44+ 功能描述:網絡控制器與處理器 IC Quad Ethernet Mapper RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS33Z44DK 功能描述:以太網開發工具 DS33Z44 Dev Kit RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
DS33ZH11 功能描述:網絡控制器與處理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS33ZH11+ 功能描述:網絡控制器與處理器 IC 10/100 ENETXPORT HMODE MAP IND RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流（最大值）:595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
DS34 制造商:LUMILEDS 制造商全稱:LUMILEDS 功能描述:power light source Luxeon V Emitter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*