- 您現在的位置：買賣IC網 > PDF目錄9364 > DS3501U+ (Maxim Integrated Products)IC POT NV 128POS HV 10-USOP PDF資料下載
參數資料
| 型號： | DS3501U+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/14頁 |
| 文件大小： | 0K |
| 描述： | IC POT NV 128POS HV 10-USOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 接片： | 128 |
| 電阻（歐姆）： | 10k |
| 電路數： | 1 |
| 溫度系數： | 標準值 200 ppm/°C |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 100°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-µMAX |
| 包裝： | 管件 |
| 產品目錄頁面： | 1431 (CN2011-ZH PDF) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
DS3501
High-Voltage, NV, I2C POT with Temp Sensor
and Lookup Table
10
____________________________________________________________________
Standby Mode and ICC
The DS3501 has three specified levels of supply cur-
rent. Active current during I2C communications while in
the LUT-driven mode is specified as ICC, and is the
“worst-case” supply current. Active current without I2C
communications while in the LUT driven mode is speci-
fied as the supply current: ICC2. SDA and SCL are held
statically in the high-logic level while the DS3501 con-
tinues to function in LUT-driven mode. The third level is
specified as standby mode, ISTBY. This is the lowest
possible current consumption mode.
Standby mode is enabled with CR2.0 = 1. All internal
operations are halted including internal temperature
sensor results. Consequently, WR’s position will not
change, and will remain in the last state that was
loaded into WR. I2C will, however, continue to function,
and once CR2.0 = 0, the DS3501 will resume normal
operation after the first temperature conversion cycle is
complete (tFRAME).
Slave Address Byte and Address Pins
The slave address byte consists of a 7-bit slave
address plus a R/W bit (see Figure 2). The DS3501’s
slave address is determined by the state of the A0 and
A1 address pins. These pins allow up to four devices to
reside on the same I2C bus. Address pins tied to GND
result in a 0 in the corresponding bit position in the
slave address. Conversely, address pins tied to VCC
result in a 1 in the corresponding bit positions. For
example, the DS3501’s slave address byte is 50h when
A0 and A1 pins are grounded. I2C communication is
described in detail in the
I2C Serial Interface
Description section.
I2C Serial Interface Description
I2C Definitions
The following terminology is commonly used to describe
I2C data transfers. (See Figure 3 and
I2C AC Electrical
Characteristics table for additional information.)
Master device: The master device controls the slave
devices on the bus. The master device generates SCL
clock pulses and START and STOP conditions.
Control Register 2 (CR2)
POWER-UP DEFAULT
00h
MEMORY TYPE
Volatile
0Ah
Reserved
TEN
AEN
Standby
bit7
bit0
bit7:3
Reserved
bit2
TEN: Temperature Update Enable bar. This bit is valid only in LUT Mode and LUT Adder Mode.
0 = Normal LUT operation. The WR is automatically loaded with LUTVAL+IVR or LUTVAL following each
temperature conversion.
1 = Places the potentiometer in manual mode allowing WR (09h) to be written using I2C.
bit1
AEN: Address Update Enable bar. This bit is valid only in LUT Mode and LUT Adder Mode.
0 = Normal LUT operation. LUTAR (08h) is calculated following each temperature conversion that points to the
corresponding location in the LUT.
1 = Disables automatic updates of LUTAR. This allow the user to directly write to the LUTAR register in order to
exercise LUT values and functionality.
bit0
Standby:
0 = Normal operating mode.
1 = Standby Mode. Places the DS3501 in a low-power consumption state specified by ISTBY. The I2C interface
is still active in this state.
0
1
0
R/W
A0
A1
0
MSB
LSB
SLAVE ADDRESS*
*THE SLAVE ADDRESS IS DETERMINED BY ADDRESS PINS A0, A1.
Figure 2. DS3501 Slave Address Byte
相關PDF資料 |
PDF描述 |
|---|---|
| MS3121E14-12PW | CONN RCPT 12POS CBL MNT W/PINS |
| VI-23N-MY-F1 | CONVERTER MOD DC/DC 18.5V 50W |
| MS3121E14-12P | CONN RCPT 12POS CBL MNT W/PINS |
| VI-23M-MY-F4 | CONVERTER MOD DC/DC 10V 50W |
| MS27473T20F2P | CONN PLUG 65POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3501U+ | 功能描述:數字電位計 IC High-Voltage NV I2C w/Temp Sensor & LUT RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS3501U+H | 功能描述:數字電位計 IC High-Voltage NV I2C w/Temp Sensor & LUT RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS3501U+T&R | 制造商:Maxim Integrated Products 功能描述:TEMP SENSOR DGTL I2C 10USOP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT NV 128POS HV 10-USOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs High-Voltage NV I2C w/Temp Sensor & LUT |
| DS3501U+T&R/C | 制造商:Maxim Integrated Products 功能描述:15V NV I2C POT W/TEMP SEN&LUT CUSTO - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT NV 128POS HV 10-USOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs High-Voltage NV I2C w/Temp Sensor & LUT |
| DS3501U+T&R/H | 制造商:Maxim Integrated Products 功能描述:GREEN-I2C POT W/TMP SEN&LUT T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC POT NV 128POS HV 10-USOP 制造商:Maxim Integrated Products 功能描述:Digital Potentiometer ICs High-Voltage NV I2C w/Temp Sensor & LUT |
發布緊急采購，3分鐘左右您將得到回復。