參數資料
型號: DS3903
元件分類: 數字電位計
英文描述: Triple 128-Position Nonvolatile Digital Potentiometer
中文描述: 三路、128抽頭、非易失數字電位器
文件頁數: 4/11頁
文件大?。?/td> 619K
代理商: DS3903
D
Triple 128-Position Nonvolatile
Digital Potentiometer
4
______________________________________________________________________
Note 1:
Note 2:
All voltages are referenced to ground.
I
STBY
specified for V
CC
equal to 3.0V and 5.0V while control port logic pins are driven to the appropriate
logic levels. Appropriate logic levels specify that logic inputs are within a 0.5V of ground or V
CC
for the
corresponding inactive state. WP must be disconnected or connected high.
I/O pins of fast mode devices must not obstruct the SDA and SCL lines if V
CC
is switched off.
A fast mode device can be used in a standard mode system, but the requirement t
SU:DAT
> 250ns must
then be met. This is automatically the case if the device does not stretch the low period of the SCL signal.
If such a device does stretch the low period of the SCL signal, it must output the next data bit to the SDA
line t
RMAX
+ t
SU:DAT
= 1000ns + 250ns = 1250ns before the SCL line is released.
After this period, the first clock pulse is generated.
The maximum t
HD:DAT
has only to be met if the device does not stretch the low period (t
LOW
) of the
SCL signal.
A device must internally provide a hold time of at least 300ns for the SDA signal (referred to the V
IN MIN
of
the SCL signal) in order to bridge the undefined region of the falling edge of SCL.
C
B
—total capacitance of one bus line in picofarads, timing referenced to 0.9 x V
CC
and 0.1 x V
CC
.
EEPROM write begins after a stop condition occurs.
Absolute linearity is used to measure expected wiper voltage as determined by wiper position in a
voltage-divider configuration.
Relative linearity is used to determine the change of wiper voltage between two adjacent wiper positions
in a voltage-divider configuration.
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
Note 10:
Note 11:
Typical Operating Characteristics
(V
CC
= 5.0V, 10k
plots apply to both pot0 and pot2, T
A
= +25°C unless otherwise noted.)
10
20
30
40
50
60
70
80
90
100
0
W-L RESISTANCE
vs. WIPER SETTING (90k
)
D
WIPER SETTING
W
)
125
100
75
50
25
0
W-L RESISTANCE
vs. WIPER SETTING (10k
)
D
WIPER SETTING
W
)
125
100
75
50
25
0
2
4
6
8
10
0
STANDBY SUPPLY CURRENT
vs. TEMPERATURE
D
TEMPERATURE (
°
C)
S
μ
A
50
40
-30 -20 -10
10 20
0
30
20
40
60
80
100
120
140
160
0
-40
60 70 80
V
CC
= 5V
V
CC
= 3V
相關PDF資料
PDF描述
DS3930 Hex Nonvolatile Potentiometer with I/O and Memory
DS3930E Hex Nonvolatile Potentiometer with I/O and Memory
DS3930 RELIABILITY REPORT FOR DS3930, REV A1
DS409-4BNC Industrial Control IC
DS409-4SMA Industrial Control IC
相關代理商/技術參數
參數描述
DS3903E 功能描述:IC POT NV TRIPLE 128POS 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數字電位器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 接片:32 電阻(歐姆):50k 電路數:1 溫度系數:標準值 50 ppm/°C 存儲器類型:易失 接口:3 線串行(芯片選擇,遞增,增/減) 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 細型,TSOT-23-6 供應商設備封裝:TSOT-23-6 包裝:帶卷 (TR)
DS3903E+ 制造商:Maxim Integrated Products 功能描述:DGTL POTENTIOMETER 128POS 10.5KOHM/90KOHM TRIPLE 20TSSOP - Rail/Tube
DS3903E-020 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel
DS3903E-020/R 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Triple 128-Position Nonvolatile Digital Potentiometer
DS3903E-020/T 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Triple 128-Position Nonvolatile Digital Potentiometer