- 您現在的位置：買賣IC網 > PDF目錄9183 > DS3904U-010+T&R (Maxim Integrated Products)IC POT NV TRIPLE 128POS 8-USOP PDF資料下載
參數資料
| 型號： | DS3904U-010+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/11頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC POT NV TRIPLE 128POS 8-USOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 3,000 |
| 接片： | 128 |
| 電阻（歐姆）： | 10k，20k，20k |
| 電路數： | 3 |
| 溫度系數： | 標準值 123 ppm/°C; 標準值 173 ppm/°C; |
| 存儲器類型： | 非易失 |
| 接口： | I²C（設備位址） |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 帶卷 (TR) |
DS3904/DS3905
Triple 128-Position Nonvolatile Digital
Variable Resistor/Switch
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 11
2007 Maxim Integrated Products
is a registered trademark of Maxim Integrated Products, Inc.
is a registered trademark of Dallas Semiconductor Corporation.
The DS3904/DS3905 can operate in the following three
modes:
1)
Slave Receiver Mode: Serial data and clock are
received through SDA and SCL, respectively. After
each byte is received, an acknowledge bit is trans-
mitted. Start and stop conditions are recognized as
the beginning and end of a serial transfer. Address
recognition is performed by hardware after the
slave (device) address and direction bit has been
received.
2)
Slave Transmitter Mode: The first byte is received
and handled as in the slave receiver mode.
However, in this mode the direction bit indicates
that the transfer direction is reversed. Serial data is
transmitted on SDA by the DS3904/DS3905 while
the serial clock is input on SCL. Start and stop con-
ditions are recognized as the beginning and end of
a serial transfer.
3)
Slave Address: The command/control byte is the
first byte received following the start condition from
the master device. The command/control byte con-
sists of a 4-bit device identifier. For the DS3904, the
identifier is followed by the device-select bits 0, 0,
and A0. For the DS3905, the identifier is followed by
the device-select bits A2, A1, A0. The device identi-
fier is used by the master device to select which
device is to be accessed. When reading or writing
the DS3904/DS3905, the device-select bits must
match the device-select pin(s). The last bit of the
command/control byte (R/W) defines the operation
to be performed. When set to a ‘1’, a read operation
is selected, and when set to a ‘0’, a write operation
is selected.
Following the start condition, the DS3904/DS3905 moni-
tor the SDA bus checking the device-type identifier
being transmitted. Upon receiving the control code, the
appropriate device address bit, and the read/write bit,
the slave device outputs an acknowledge signal on the
SDA line.
Applications Information
Power-Supply Decoupling
To achieve the best results when using the DS3904/
DS3905, decouple the power supply with a 0.01F or
0.1F capacitor. Use a high-quality ceramic surface-
mount capacitor. Surface-mount components minimize
lead inductance, which improves performance, and
ceramic capacitors tend to have adequate high-fre-
quency response for decoupling applications.
High Resistor Terminal Voltage
It is possible to have a voltage on the resistor-high termi-
nals that is higher than the voltage connected to VCC.
For instance, connecting VCC to 3.0V while one or more
of the resistor high terminals are connected to 5.0V
allows a 3V system to control a 5V system. The 5.5V
maximum still applies to the limit on the resistor high ter-
minals regardless of the voltage present on VCC.
Package Information
For the latest package outline information, go to
www.maxim-ic.com/DallasPackInfo.
相關PDF資料 |
PDF描述 |
|---|---|
| VI-2TZ-MV-B1 | CONVERTER MOD DC/DC 2V 60W |
| X9251TV24Z | IC XDCP QUAD 256TAP 100K 24TSSOP |
| X9259TS24Z | IC XDCP QUAD 256TAP 100K 24-SOIC |
| V28A12H200BF | CONVERTER MOD DC/DC 12V 200W |
| V28A3V3H150BF | CONVERTER MOD DC/DC 3.3V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS3904U-020 | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS3904U-020/T&R | 制造商:Maxim Integrated Products 功能描述:TRIPLE NON VOLATILE DIGITAL RESISTO - Tape and Reel |
| DS3904U-020/T&R | 功能描述:數字電位計 IC RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS3904U-020+ | 功能描述:數字電位計 IC Triple 128-Position Nonvolatile RoHS:否 制造商:Maxim Integrated 電阻:200 Ohms 溫度系數:35 PPM / C 容差:25 % POT 數量:Dual 每 POT 分接頭:256 弧刷存儲器:Volatile 緩沖刷: 數字接口:Serial (3-Wire, SPI) 描述/功能:Dual Volatile Low Voltage Linear Taper Digital Potentiometer 工作電源電壓:1.7 V to 5.5 V 電源電流:27 uA 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:TQFN-16 封裝:Reel |
| DS3904U-020+ | 制造商:Maxim Integrated Products 功能描述:SEMICONDUCTOR |
發布緊急采購，3分鐘左右您將得到回復。