- 您現(xiàn)在的位置：買賣IC網 > PDF目錄1916 > DS4830T+ (Maxim Integrated Products)MCU 16B CTRL CALIBR MON 40-TQFN PDF資料下載
參數資料
| 型號： | DS4830T+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 17/30頁 |
| 文件大?。?/td> | 0K |
| 描述： | MCU 16B CTRL CALIBR MON 40-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 60 |
| 系列： | MAXQ® |
| 核心處理器： | RISC |
| 芯體尺寸： | 16-位 |
| 速度： | 10MHz |
| 連通性： | 3 線，I²C，SPI |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 31 |
| 程序存儲器容量： | 64KB（32K x 16） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 16 |
| 電壓 - 電源 (Vcc/Vdd)： | 3 V ~ 3.6 V |
| 數據轉換器： | A/D 18x13b，D/A 8x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 40-WFQFN 裸露焊盤 |
| 包裝： | 管件 |
| 其它名稱： | 90-4830T+000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
DS4830
Optical Microcontroller
24
Maxim Integrated
Analog-to-Digital Converter
and Sample/Hold
The analog-to-digital converter (ADC) controller is the
digital interface block between the CPU and the ADC. It
provides all the necessary controls to the ADC and the
CPU interface. The ADC uses a set of SFRs for configur-
ing the ADC in desired mode of operation.
The device contains a 13-bit ADC with an input mux
(Figure 9). The mux selects the ADC input from 16 single-
ended or eight differential inputs. Additionally, the chan-
nels can be configured to convert internal and external
temperature, VDD, internal reference, or REFINA/B. Two
channels can be programmed to be sample/hold inputs.
The internal channel is used exclusively to measure the
die temperature. The SFR registers control the ADC.
ADC
When used in voltage input mode, the voltage applied on
the corresponding channel (differential or single-ended)
is converted to a digital readout. The ADC can be set up
to continuously poll selected input channels (continuous-
sequence mode) or run a short burst of conversions
and enter a shutdown mode to conserve power (single-
sequence mode).
In voltage mode there are four full-scale values that can
be programmed. These values can be trimmed by modi-
fying the associated gain registers (ADCG1, ADCG2,
ADCG3, ADCG4). By default these are set to 1.2V, 0.6V,
2.4V, and 4.8V full scale.
The ADCCLK is derived from the system clock with divi-
sion ratio defined by the ADC control register. An A/D
conversion takes 15 ADCCLK cycles to complete with
additional four core clocks used for data processing.
Internally every channel is converted twice and the aver-
age of two conversions is written to the data buffer. This
gives each conversion result in (30 x ADC Clock Period
+ 800ns). ADC sampling rate is approximately 40ksps
for the fastest ADC clock (core clock/8). In applications
where extending the acquisition time is desired, the sam-
ple can be acquired over a prolonged period determined
by the ADC control register.
Each ADC channel can have its own configuration, such
as differential mode select, data alignment select, acqui-
sition extension enable, and ADC gain select, etc. The
ADC also has 24 (0 to 23) 16-bit data buffers for con-
version result storage. The ADC data available interrupt
flag (ADDAI) can be configured to trigger an interrupt
following a predetermined number of samples. Once set,
ADDAI can be cleared by software or at the start of a
conversion process.
Sample/Hold
Pin combinations GP2-GP3 and GP12-GP13 can be
used for sample/hold conversions if enabled in the SHCN
register. These two can be independently enabled or
disabled by writing a 1 or 0 to their corresponding bit
locations in SHCN register. A data buffer location is
reserved for each channel. When a particular channel is
enabled, a sample of the input voltage is taken when a
signal is issued on the SHEN pin, converted and stored
in the corresponding data buffer.
The two sample/hold channels can sample simultane-
ously on the same SHEN signal or different SHEN signals
depending on the SH_DUAL bit in the SHCN SFR.
The sample/hold data available interrupt flag (SHnDAI)
can be configured to trigger an interrupt following sam-
ple completion. Once set, SHnDAI can be cleared by
software.
Each sample/hold circuit consists of a sampling capaci-
tor, charge injection nulling switches, and a buffer.
Also included is a discharge circuit used to discharge
parasitic capacitance on the input node and the sample
capacitor before sampling begins. The negative input
pins can be used to reduce ground offsets and noise.
Figure 9. ADC Block Diagram
ADC-S[15:0]
ADC-D[7:0][P/N]
ADC-SHP[1:0]
ADC-SHN[1:0]
ADC-REFIN[A/B]
ADC-VDD
ADC-VREF_2.5V
ADC-TEXT_A(+/-)
ADC-TEXT_B(+/-)
ADC-TINT
MUX
ADCONV
(START CONVERSATION)
ADCCFG
PGA
ADGAIN
13-BIT ADC
相關PDF資料 |
PDF描述 |
|---|---|
| DS5000FP-16 | IC MODULE MICRO 16MHZ FLATPACK |
| DS5000T-32-16+ | IC MPU W/RTC 32KB 16MHZ 40-DIP |
| DS5001FP-16N | IC MPU 128K 16MHZ IND 80-TQFP |
| DS5002FMN-16 | IC MPU SECURE 16MHZ IND 80-TQFP |
| DS72612RP80FPV | IC SUPERH MPU ROMLESS 176LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS4830T+ | 功能描述:16位微控制器 - MCU Control Calibration & Opt Trans Mtr RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| DS4830T+T | 功能描述:16位微控制器 - MCU Control Calibration & Opt Trans Mtr RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT |
| DS485 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Low Power RS-485/RS-422 Multipoint Transceiver |
| DS485M | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| DS485M | 制造商:Texas Instruments 功能描述:RS485/422 LOW POWER TRNSCVR SOIC8 |
發(fā)布緊急采購，3分鐘左右您將得到回復。