- 您現在的位置：買賣IC網 > PDF目錄1916 > DS8023-RRX+ (Maxim Integrated Products)IC INTERFACE SMART CARD 28-SOIC PDF資料下載
參數資料
| 型號： | DS8023-RRX+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/17頁 |
| 文件大小： | 0K |
| 描述： | IC INTERFACE SMART CARD 28-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 212 |
| 應用： | 智能卡 |
| 接口： | 模擬 |
| 電源電壓： | 2.7 V ~ 6 V |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
| 安裝類型： | 表面貼裝 |
| 配用： | DS8023-KIT-ND - EVALUATION KIT FOR DS8023 |
DS8023
Smart Card Interface
14
Maxim Integrated
Smart Card Power Select
The DS8023 supports three smart card VCC voltages:
1.8V, 3V, and 5V. The power select is controlled by the
1_8V and 5V/3V signals as shown in Table 3. The 1_8V
signal has priority over 5V/3V. When 1_8V is asserted
high, 1.8V is applied to VCC when the smart card is
active. When 1_8V is deasserted, 5V/3V dictates VCC
power range. VCC is 5V if 5V/3V is asserted to a logic-
high state, and VCC is 3V if 5V/3V is pulled to a
logic-low state. Care must be exercised when switching
from one VCC power selection to the other. If both 1_8V
and 5V/3V are high with CMDVCC high at the same
time, the DS8023 enters stop mode. To avoid acciden-
tal entry into stop mode, the state of 1_8V and 5V/3V
must not be changed simultaneously. A minimum delay
of 100ns should be observed between changing the
states of 1_8V and 5V/3V. See Figure 9 for the recom-
mended sequence of changing the VCC range.
VCC SELECT
STOP MODE
1.8V
3V
5V
1_8V
5V/3V
CMDVCC
Figure 9. Smart Card Power Select
Table 3. VCC Select and Operation Mode
1_8V
5V/3V
CMDVCC
VCC SELECT (V)
CARD INTERFACE STATUS
0
3
Activated
0
1
3
Deactivated
0
1
0
5
Activated
0
1
5
Deactivated
1
0
1.8
Activated
1
0
1
1.8
Deactivated
1
0
1.8
Reserved (Activated)
1
1.8
Not Applicable—Stop Mode
相關PDF資料 |
PDF描述 |
|---|---|
| DS80C310-ECG | IC MCU HI SPEED 25MHZ 44-TQFP |
| DS80C320-ECL/T&R | IC MCU HI SPEED 33MHZ 44-TQFP |
| DS80C390-FNR | IC MPU CAN DUAL HS IND 64-LQFP |
| DS80C400-FNY | IC MCU 75MHZ 16MB HP 100-LQFP |
| DS80C410-FNY+ | IC MCU 75MHZ 16MB HP 100-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS8023-RRX+ | 功能描述:接口 - 專用 Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS8023-RRX+T&R | 制造商:Maxim Integrated Products 功能描述:DS8023 SMART CARD INT 28 SOIC T&R - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC INTERFACE SMART CARD 28-SOIC |
| DS8023-RRX+T&R | 功能描述:接口 - 專用 Smart Card Interface RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| DS8024 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:智能卡接口 |
| DS8024_V3 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Smart Card Interface |
發布緊急采購，3分鐘左右您將得到回復。