參數資料
型號: DS80C320-ECG
廠商: Maxim Integrated Products
文件頁數: 34/38頁
文件大?。?/td> 0K
描述: IC MCU HI SPEED 25MHZ 44-TQFP
產品培訓模塊: Lead (SnPb) Finish for COTS
產品變化通告: Product Discontinuation 20/Feb/2012
標準包裝: 160
系列: 80C
核心處理器: 8051
芯體尺寸: 8-位
速度: 25MHz
連通性: EBI/EMI,SIO,UART/USART
外圍設備: 電源故障復位,WDT
輸入/輸出數: 32
程序存儲器類型: ROMless
RAM 容量: 256 x 8
電壓 - 電源 (Vcc/Vdd): 4.5 V ~ 5.5 V
振蕩器型: 外部
工作溫度: 0°C ~ 70°C
封裝/外殼: 44-TQFP
包裝: 托盤
其它名稱: DS80C320ECG
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
5 of 38
PIN DESCRIPTION (continued)
PIN
DIP
PLCC
TQFP
NAME
FUNCTION
21
24
18
A8 (P2.0)
22
25
19
A9 (P2.1)
23
26
20
A10 (P2.2)
24
27
21
A11 (P2.3)
25
28
22
A12 (P2.4)
26
29
23
A13 (P2.5)
27
30
24
A14 (P2.6)
28
31
25
A15 (P2.7)
Port 2, Output. Port 2 serves as the MSB for external addressing.
P2.7 is A15 and P2.0 is A8. The device will automatically place the
MSB of an address on P2 for external ROM and RAM access.
Although Port 2 can be accessed like an ordinary I/O port, the value
stored on the Port 2 latch will never be seen on the pins (due to
memory access). Therefore, writing to Port 2 in software is only
useful for the instructions MOVX A, @Ri or MOVX @Ri, A. These
instructions use the Port 2 internal latch to supply the external address
MSB. In this case, the Port 2 latch value will be supplied as the
address information.
Port 3, Input/Output. Port 3 functions as both an 8-bit, bidirectional
I/O port and an alternate functional interface for External Interrupts,
Serial Port 0, Timer 0 & 1 Inputs, RD and WR strobes. The reset
condition of Port 3 is with all bits at logic 1. In this state, a weak
pullup holds the port high. This condition also serves as an input
mode, since any external circuit that writes to the port will overcome
the weak pullup. When software writes a 0 to any port pin, the device
will activate a strong pulldown that remains on until either a 1 is
written or a reset occurs. Writing a 1 after the port has been at 0 will
cause a strong transition driver to turn on, followed by a weaker
sustaining pullup. Once the momentary strong driver turns off, the
port once again becomes both the output high and input state. The
alternate modes of Port 3 are outlined below:
PIN
DIP
PLCC
TQFP
PORT
ALTERNATE
MODE
10
11
5
P3.0
RXD0
Serial Port 0 Input
11
13
7
P3.1
TXD0
Serial Port 0 Output
12
14
8
P3.2
INT0
External Interrupt 0
13
15
9
P3.3
INT1
External Interrupt 1
14
16
10
P3.4
T0
Timer 0 External Input
15
17
11
P3.5
T1
Timer 1 External Input
16
18
12
P3.6
WR
External Data Memory Write
Strobe
10–17
11, 13–
19
5, 7–13
P3.0–P3.7
17
19
13
P3.7
RD
External Data Memory Read
Strobe
31
35
29
EA
External Access, Active-Low Input. This pin must be connected to
ground for proper operation.
12, 34,
1*
6, 28,
39*
N.C.
No Connection (Reserved). These pins should not be connected.
They are reserved for use with future devices in this family.
*These pins are reserved for additional ground pins on future products.
相關PDF資料
PDF描述
PK60X256VMD100 IC ARM CORTEX MCU 256K 144-MAP
PK60X256VLQ100 IC ARM CORTEX MCU 256K 144-LQFP
PK60N256VMD100 IC ARM CORTEX MCU 256K 144-MAP
PK40X256VLQ100 IC ARM CORTEX MCU 256K 144-LQFP
1061541001 ADPT EMI-SHLD SIMPLEX SC-SC BEIG
相關代理商/技術參數
參數描述
DS80C320-ECG/T&R 制造商:Maxim Integrated Products 功能描述:IC MCU HI SPEED 25MHZ 44-TQFP
DS80C320-ECG/T&R 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C320-ECG+ 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C320-ECL 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C320-ECL/T&R 制造商:Maxim Integrated Products 功能描述:IC MCU HI SPEED 33MHZ 44-TQFP