- 您現在的位置：買賣IC網 > PDF目錄376981 > DS80C320 (Maxim Integrated Products, Inc.) High-Speed/Low-Power Microcontrollers PDF資料下載
參數資料
| 型號： | DS80C320 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | High-Speed/Low-Power Microcontrollers |
| 中文描述： | 高速/低功耗微控制器 |
| 文件頁數： | 21/42頁 |
| 文件大?。?/td> | 1501K |
| 代理商： | DS80C320 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
DS80C320/DS80C323
21 of 42
NOTES FOR DS80C320 DC ELECTRICAL CHARACTERISTICS:
All parameters apply to both commercial and industrial temperature operation unless otherwise noted.
1. All voltages are referenced to ground.
2. Active current is measured with a 25 MHz clock source driving XTAL1, V
CC
=RST=5.5V, all other
pins disconnected.
3. Idle mode current is measured with a 25 MHz clock source driving XTAL1, V
CC
=5.5V, RST at
ground, all other pins disconnected.
4. Stop mode current measured with XTAL1 and RST grounded, V
CC
=5.5V, all other pins disconnected.
when addressing external memory.
5. When addressing external memory.
6. RST=V
CC
. This condition mimics operation of pins in I/O mode.
7. During a 0 to 1 transition, a one-shot drives the ports hard for two clock cycles. This measurement
reflects port in transition mode.
8. Ports 1, 2, and 3 source transition current when being pulled down externally. It reaches its maximum
at approximately 2V.
9. 0.45<V
IN
<V
CC
. Not a high impedance input. This port is a weak address holding latch because Port 0
is dedicated as an address bus on the DS80C320. Peak current occurs near the input transition point of
the latch, approximately 2V.
10. Over the industrial temperature range, this specification has a maximum value of 200 μA.
11. This is the current required from an external circuit to hold a logic low level on an I/O pin while the
corresponding port latch bit is set to 1. This is only the current required to
hold
the low level;
transitions from 1 to 0 on an I/O pin will also have to overcome the transition current.
12. Device operating range is 4.5V to 5.5V; however, device is tested to 4.0V to ensure proper operation
at minimum V
RST
.
相關PDF資料 |
PDF描述 |
|---|---|
| DS80C320-ECG | Strain Relief |
| DS80C320-ECL | High-Speed/Low-Power Microcontrollers |
| DS80C320-ENG | High-Speed/Low-Power Microcontrollers |
| DS80C320-ENL | High-Speed/Low-Power Microcontrollers |
| DS80C320-MCG | High-Speed/Low-Power Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C320_06 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:High-Speed/Low-Power Microcontrollers |
| DS80C320+ENL | 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC ROMLESS 5V 44TQFP - Trays |
| DS80C320+FCG | 制造商:Maxim Integrated Products 功能描述:MICRO HI SPD 44PQFP 25MHZ PB-FREE - Trays |
| DS80C320+FNG | 制造商:Maxim Integrated Products 功能描述:MICRO HS 44MQFP 25MHZ IND PB-FREE - Trays |
| DS80C320+MCG | 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC ROMLESS 5V 40PDIP - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC 8BIT CPU CMOS 80C320 DIP40 制造商:Maxim Integrated Products 功能描述:IC, 8BIT CPU CMOS, 80C320, DIP40 制造商:Maxim Integrated Products 功能描述:IC, 8BIT CPU CMOS, 80C320, DIP40; Controller Family/Series:(8051) 8052; Core Size:8bit; No. of I/O's:32; Supply Voltage Min:4.5V; Supply Voltage Max:5.5V; Digital IC Case Style:DIP; No. of Pins:40; RAM Memory Size:256Byte; CPU ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。