參數資料
型號: DS80C323-ECD
廠商: Maxim Integrated Products
文件頁數: 8/38頁
文件大?。?/td> 0K
描述: IC MCU HI SPEED 18MHZ 44-TQFP
產品培訓模塊: Lead (SnPb) Finish for COTS
產品變化通告: Product Discontinuation 20/Feb/2012
標準包裝: 160
系列: 80C
核心處理器: 8051
芯體尺寸: 8-位
速度: 18MHz
連通性: EBI/EMI,SIO,UART/USART
外圍設備: 電源故障復位,WDT
輸入/輸出數: 32
程序存儲器類型: ROMless
RAM 容量: 256 x 8
電壓 - 電源 (Vcc/Vdd): 4.5 V ~ 5.5 V
振蕩器型: 外部
工作溫度: 0°C ~ 70°C
封裝/外殼: 44-TQFP
包裝: 托盤
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
16 of 38
a 25MHz crystal frequency. Note that once the counter chain has reached a conclusion, the optional
interrupt is generated. Regardless of whether the user enables this interrupt, there are then 512 clocks left
until a reset occurs. There are 5 control bits in special function registers that affect the Watchdog Timer
and two status flags that report to the user. The Reset Watchdog Timer bit (WDCON.0) should be
asserted prior to modifying the Watchdog Timer Mode Select bits (WD1, WD0) to avoid corruption of
the watchdog count.
WDIF (WDCON.3) is the interrupt flag that is set when there are 512 clocks remaining until a reset
occurs. WTRF (WDCON.2) is the flag that is set when a Watchdog reset has occurred. This allows the
application software to determine the source of a reset.
Setting the EWT (WDCON.1) bit enables the Watchdog Timer. The bit is protected by timed access.
Setting the RWT (WDCON.0) bit restarts the Watchdog Timer for another full interval. Application
software must set this bit prior to the timeout. As mentioned previously, WD1 and 0 (CKCON .7 and 6)
select the timeout. Finally, the Watchdog Interrupt is enabled using EWDI (EIE.4).
INTERRUPTS
The DS80C320/DS80C323 provide 13 sources of interrupt with three priority levels. The Power-fail
Interrupt (PFI), if enabled, always has the highest priority. There are two remaining user-selectable
priorities: high and low. If two interrupts that have the same priority occur simultaneously, the natural
precedence given in Table 4 determines which is acted upon. Except for the PFI, all interrupts that are
new to the 8051 family have a lower natural priority than the originals.
Table 4. Interrupt Priority
NAME
FUNCTION
VECTOR
NATURAL
PRIORITY
OLD/NEW
PFI
Power-Fail Interrupt
33h j
1
New
INT0
External Interrupt 0
03h
2
Old
TF0
Timer 0
0Bh
3
Old
INT1
External Interrupt 1
13h
4
Old
TF1
Timer 1
1Bh
5
Old
SCON0
TI0 or RI0 from Serial Port 0
23h
6
Old
TF2
Timer 2
2Bh
7
Old
SCON1
TI1 or RI1 from Serial Port 1
3Bh
8
New
INT2
External Interrupt 2
43h
9
New
INT3
External Interrupt 3
4Bh
10
New
INT4
External Interrupt 4
53h
11
New
INT5
External Interrupt 5
5Bh
12
New
WDTI
Watchdog Timeout Interrupt
63h
13
New
相關PDF資料
PDF描述
MCF51JM128VLH IC MCU 128/16K FLASH/SRAM 64LQFP
MC908AP16CFBE IC MCU 16K FLASH 8MHZ 44QFP
MC908AP16CBE IC MCU 16K FLASH 8MHZ 42DIP
MC9S08DZ32AMLH IC MCU 32K FLASH 2K RAM 64-LQFP
DS87C520-ECL IC MCU EPROM/ROM 33MHZ HS 44TQFP
相關代理商/技術參數
參數描述
DS80C323-ECD+ 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C323-ECD+T&R 制造商:Maxim Integrated Products 功能描述:MXMDS80C323-ECD+T&R HIGH-SPEED/LOW-POWER 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC ROMLESS 3V 44TQFP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MCU 18MHZ HS/LP 44-TQFP
DS80C323-ECD+T&R 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C323-ECG 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide
DS80C323-ECL 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:High-Speed Microcontroller User Guide