- 您現在的位置：買賣IC網 > PDF目錄1916 > DS87C530-KCL (Maxim Integrated Products)IC MCU EPR/ROM W/RTC 33MZ 52CLCC PDF資料下載
參數資料
| 型號： | DS87C530-KCL |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 11/45頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU EPR/ROM W/RTC 33MZ 52CLCC |
| 標準包裝： | 23 |
| 系列： | 87C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 33MHz |
| 連通性： | EBI/EMI，SIO，UART/USART |
| 外圍設備： | 電源故障復位，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器容量： | 16KB（16K x 8） |
| 程序存儲器類型： | EPROM，UV |
| RAM 容量： | 1K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振蕩器型： | 外部 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 52-CLCC，開窗（J 形引線） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
DS87C530/DS83C530 EPROM/ROM Microcontrollers with Real-Time Clock
19 of 45
Switchback
To return to a 4-clock rate from PMM, software can simply select the CD1 and CD0 clock control bits to
the 4 clocks per cycle state. However, the DS87C530/DS83C530 provide several hardware alternatives
for automatic Switchback. If Switchback is enabled, then the device will automatically return to a 4-clock
per cycle speed when an interrupt occurs from an enabled, valid external interrupt source. A Switchback
will also occur when a UART detects the beginning of a serial start bit if the serial receiver is enabled
(REN = 1). Note the beginning of a start bit does not generate an interrupt; this occurs on reception of a
complete serial word. The automatic Switchback on detection of a start bit allows hardware to correct
baud rates in time for a proper serial reception. A Switchback will also occur when a byte is written to the
SBUF0 or SBUF1 for transmission.
Switchback is enabled by setting the SWB bit (PMR.5) to a 1 in software. For an external interrupt,
Switchback will occur only if the interrupt source could really generate the interrupt. For example, if
INT0
is enabled but has a low priority setting, then Switchback will not occur on INT0 if the CPU is
servicing a high priority interrupt.
Status
Information in the Status register assists decisions about switching into PMM. This register contains
information about the level of active interrupts and the activity on the serial ports.
The DS87C530/DS83C530 support three levels of interrupt priority. These levels are Power-fail, High,
and Low. Bits STATUS.7–5 indicate the service status of each level. If PIP (Power-fail Interrupt Priority;
STATUS. 7) is 1, then the processor is servicing this level. If either HIP (High Interrupt Priority;
STATUS.6) or LIP (Low Interrupt Priority; STATUS.5) is high, then the corresponding level is in
service.
Software should not rely on a lower priority level interrupt source to remove PMM (Switchback) when a
higher level is in service. Check the current priority service level before entering PMM. If the current
service level locks out a desired Switchback source, then it would be advisable to wait until this condition
clears before entering PMM.
Alternately, software can prevent an undesired exit from PMM by entering a low priority interrupt service
level before entering PMM. This will prevent other low priority interrupts from causing a Switchback.
Status also contains information about the state of the serial ports. Serial Port Zero Receive Activity
(SPRA0; STATUS.0) indicates a serial word is being received on Serial Port 0 when this bit is set to a 1.
Serial Port 0 Transmit Activity (SPTA0; STATUS.1) indicates that the serial port is still shifting out a
serial transmission. STATUS.2 and STATUS.3 provide the same information for Serial Port 1,
respectively. These bits should be interrogated before entering PMM1 or PMM2 to ensure that no serial
port operations are in progress. Changing the clock divisor rate during a serial transmission or reception
will corrupt the operation.
相關PDF資料 |
PDF描述 |
|---|---|
| DS87C550-QCL+ | IC MCU EPROM ADC/PWM HS 68-PLCC |
| DS89C450-ENL | IC MCU FLASH 64KB 33MHZ 44-TQFP |
| DS9034PCI | IC SRAM NV TIMEKEEPING POWERCAP |
| DS9034PCX | PCM W/CRYSTAL NV SRAM SNAP-ON |
| DS9092L+ | IBUTTON PROBE PANEL MOUNT W/LED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS87C530-QCL | 功能描述:8位微控制器 -MCU EPROM MCU w/RTC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS87C530-QCL+ | 功能描述:8位微控制器 -MCU EPROM MCU w/RTC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS87C530-QEL | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS87C530-QNL | 功能描述:8位微控制器 -MCU EPROM MCU w/RTC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。