- 您現在的位置：買賣IC網 > PDF目錄376984 > DS89C440-MNL Ultra-High-Speed Flash Microcontrollers PDF資料下載
參數資料
| 型號： | DS89C440-MNL |
| 英文描述： | Ultra-High-Speed Flash Microcontrollers |
| 中文描述： | 超高速閃存微控制器 |
| 文件頁數： | 23/48頁 |
| 文件大小： | 656K |
| 代理商： | DS89C440-MNL |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
DS89C430/DS89C440/DS89C450 Ultra-High-Speed Flash Microcontrollers
23 of 48
Note:
The read/write accessibility of the flash memory during in-application programming is not affected by the
state of the lock bits. However, the lock bits do affect the read/write accessibility in ROM loader and parallel
programming modes.
In-Application Programming by User Software
The DS89C430 supports in-application programming of on-chip flash memory by user software. In-application
programming is initiated by writing a flash command into the flash control (FCNTL:D5h) register to enable the flash
memory for erase/program/verify operations. Address and data are input into the MMU through the flash data
(FDATA:D6h) register. The flash command also enables read/write accesses to the FDATA. The MMU’s sequencer
provides the operation sequences and control functions to the flash memory. The MMU is designed to operate
independently from the processor, except for read/write access to the SFRs.
Only the upper bank of the on-chip program memory can be in-application programmed by the user software. The
lower bank of the on-chip program memory contains system hardware-dependent codes that are crucial to system
operation and should not be altered during in-application programming.
All flash operations are self-timed. The user software can monitor the progress of an erase or programming
operation through the flash busy (FBUSY;FCNTL.7) bit with a reset value at logic 1. A selected operation
automatically starts when required data is written to the FDATA SFR. The MMU clears the FBUSY bit to indicate
the start of a write/erase operation. The FBUSY bit may not change state for up to 1 s after the operation is
requested. During this time, the application should poll the status of the FBUSY bit waiting for it to change state.
This bit is held low until either the end of the operation or until an error indicator is returned. A flash operating
failure terminates the current operation and sets the flash error flag (FERR;FCNTL.6) to logic 1. Both the busy and
error flags are read-only bits.
Read/write access during in-application programming is not affected by the state of the lock bits.
A sample programming sequence for a "w
rite upper program memory bank
" is shown below. The command must be
reentered each time an operation is requested, i.e., it is not permissible to issue the “write upper program memory
bank” command once and then repeatedly load address and data values to program a block of memory.
1. Make sure the
FBUSY
bit is 1 to indicate flash MMU is idle.
2. Write 0Bh to the FCNTL register using the timed access sequence.
3. Write address_MSB to the FDATA register.
4. Write address_LSB to the FDATA register.
5. Write data_value to the FDATA register.
6. Make sure the
FBUSY
bit is 0 to indicate programming has started.
7. Wait for
FBUSY
bit to return to 1 to indicate end of programming operation.
8. Make sure FERR is 0 to indicate no programming error.
The flash command (FC3–FC0;FCNTL.3:0) bits provide flash commands as listed in
Table 4
.
相關PDF資料 |
PDF描述 |
|---|---|
| DS89C440-QNL | Ultra-High-Speed Flash Microcontrollers |
| DS89C450-ENL | Ultra-High-Speed Flash Microcontrollers |
| DS89C450-MNL | Ultra-High-Speed Flash Microcontrollers |
| DS89C450-QNL | Ultra-High-Speed Flash Microcontrollers |
| DS89C430-DS89C450 | Ultra-High-Speed Flash Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS89C440-MNL+ | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS89C440-QNG | 功能描述:IC MCU FLASH 32KB 25MHZ 44-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:89C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| DS89C440-QNL | 功能描述:IC MCU FLASH 32KB 33MHZ 44-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:89C 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:260 系列:73S12xx 核心處理器:80515 芯體尺寸:8-位 速度:24MHz 連通性:I²C，智能卡，UART/USART，USB 外圍設備:LED，POR，WDT 輸入/輸出數:9 程序存儲器容量:64KB（64K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:2K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 5.5 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:68-VFQFN 裸露焊盤 包裝:管件 |
| DS89C440-QNL+ | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Ultra-High-Speed Flash Microcontrollers |
| DS89C440-XXX | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Ultra-High-Speed Flash Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。