參數資料
型號： DSKW3022
元件分類： 電源模塊
英文描述： DC-DC REG PWR SUPPLY MODULE
封裝： PLASTIC, SMD-14/24
文件頁數： 5/9頁
文件大?。?/td> 299K
代理商： DSKW3022
5
Design & Feature Considerations
Maximum Capacitive Load
The DSKW3000 series has limitation of maximum
connected capacitance at the output. The power
module may be operated in current limiting mode
during start-up, affecting the ramp-up and the startup
time.
Output Ripple Reduction
A good quality low ESR capacitor placed as close as
practicable across the load will give the best ripple and
noise performance.
To reduce output ripple, it is recommended to use
3.3uF capacitors at the output.
+Out
-Out
+Vin
-Vin
Load
DC Power
Source
+
-
Cout
Single Output
DC / DC
Converter
+Out
-Out
+Vin
-Vin
Load
DC Power
Source
+
-
Cout
Com.
Dual Output
DC / DC
Converter
Remote On/Off
The DSKW3000 has positive remote on/off logic.
Positive logic remote on/off turns the module on during
a logic high voltage on the remote on/off pin, and off
during a logic low.
Remote on/off can be controlled by an external switch
between the on/off terminal and the -Vin terminal. The
switch can be an open collector or equivalent.
Vo(+)
Vo(-)
Vi(+)
Vi(-)
ON/OFF
Overcurrent Protection
To provide protection in a fault (output overload)
condition, the unit is equipped with internal current
limiting circuitry and can endure current limiting for an
unlimited duration. At the point of current-limit inception,
the unit shifts from voltage control to current control. The
unit operates normally once the output current is brought
back into its specified range.
Soldering and Cleaning Considerations
Post solder cleaning is usually the final board
assembly process before the board or system
undergoes electrical testing. Inadequate cleaning
and/or drying may lower the reliability of a power
module and severely affect the finished circuit board
assembly test. Adequate cleaning and/or drying is
especially important for un-encapsulated and/or open
frame type power modules. For assistance on
appropriate soldering and cleaning procedures, please
contact Delta’s technical support team.
Notes:
1. These power converters require a minimum output
load to maintain specified regulation (please see
page 6 for the suggested minimum load). Operation
under no-load conditions will not damage these
modules; however, they may not meet all
specifications listed above.
2. These DC/DC converters should be externally fused
at the front end for protection.
相關PDF資料
PDF描述
DSS-2612-330R 1 ELEMENT, 33 uH, GENERAL PURPOSE INDUCTOR, SMD
DSS9NC51H223Q55J 1 FUNCTIONS, 50 V, 6 A, DATA LINE FILTER
DSS9NC52A101Q55J 1 FUNCTIONS, 100 V, 6 A, DATA LINE FILTER
DSS9NC52A220Q55J 1 FUNCTIONS, 100 V, 6 A, DATA LINE FILTER
DSS9NC52A222Q55J 1 FUNCTIONS, 100 V, 6 A, DATA LINE FILTER
相關代理商/技術參數
參數描述
DSL01-008SC5 功能描述:TVS二極管陣列 Secondary protection RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C
DSL01-010SC5 功能描述:TVS二極管陣列 Secondary Protection RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C
DSL01-016SC5 功能描述:TVS二極管陣列 Secondary protection RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C
DSL01-024SC5 功能描述:TVS二極管陣列 Secondary Protection RoHS:否 制造商:Littelfuse 極性: 通道:4 Channels 擊穿電壓: 鉗位電壓:11.5 V 工作電壓:2.5 V 峰值浪涌電流:20 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 系列: 最小工作溫度:- 40 C 最大工作溫度:+ 85 C
DSL01-XXXSC5 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:Secondary protection for DSL lines
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*