參數資料
型號： DSP56854E
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： 16-bit Digital Signal Controllers
中文描述： 16位數字信號控制器
文件頁數： 32/60頁
文件大?。?/td> 836K
代理商： DSP56854E
56854 Technical Data, Rev. 6
32
Freescale Semiconductor
4.6 External Memory Interface Timing
The External Memory Interface is designed to access static memory and peripheral devices.
Figure 4-10
shows
sample timing and parameters that are detailed in
Table 4-11
.
The timing of each parameter consists of both a fixed delay portion and a clock related portion; as well as user
controlled wait states. The equation:
t = D + P * (M + W)
should be used to determine the actual time of each parameter. The terms in the above equation are defined as:
t
parameter delay time
D
fixed portion of the delay, due to on-chip path delays.
P
the period of the system clock, which determines the execution rate of the part (i.e. when the device is
operating at 120 MHz, P = 8.33 ns).
M Fixed portion of a clock period inherent in the design. This number is adjusted to account for possible
clock duty cycle derating.
W the sum of the applicable wait state controls. See the “Wait State Controls” column of
Table 4-11
for
the applicable controls for each parameter. See the EMI chapter of the 83x Peripheral Manual for
details of what each wait state field controls.
Some of the parameters contain two sets of numbers. These parameters have two different paths and clock edges
that must be considered. Check both sets of numbers and use the smaller result. The appropriate entry may change
if the operating frequency of the part changes.
The timing of write cycles is different when WWS = 0 than when WWS > 0. Therefore, some parameters contain
two sets of numbers to account for this difference. The “Wait States Configuration” column of
Table 4-11
should
be used to make the appropriate selection.
Table 4-6 PLL Timing
Operating Conditions: V
SS
= V
SSIO
= V
SSA
= 0 V, V
DD
= 1.62-1.98V, V
DDIO
= V
DDA
=
3.0–3.6V, T
A
= –40
°
to +120
°
C, C
L
≤
50pF, f
op
= 120MHz
Characteristic
Symbol
Min
Typ
Max
Unit
External reference crystal frequency for the PLL
1
1.
The PLL is optimized for 4MHz input crystal.
2.
This is the minimum time required after the PLL setup is changed to ensure reliable operation.
An externally supplied reference clock should be as free as possible from any phase jitter for the PLL to work correctly.
f
osc
2
4
4
MHz
PLL output frequency
f
clk
40
—
240
MHz
PLL stabilization time
2
t
plls
—
1
10
ms
相關PDF資料
PDF描述
DSP56854FG120 16-bit Digital Signal Controllers
DSP56855BU120 16-bit Digital Signal Controllers
DSP56855BUE 16-bit Digital Signal Controllers
DSP56855E 16-bit Digital Signal Controllers
DSP56857BUE 16-bit Digital Signal Controllers
相關代理商/技術參數
參數描述
DSP56854FG120 功能描述:數字信號處理器和控制器 - DSP, DSC 120Mhz/120MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56854FGE 功能描述:數字信號處理器和控制器 - DSP, DSC 120Mhz/120MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSP56854PB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:56854 Digital Signal Processor Product Brief
DSP56855 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Digitial Signal Controller
DSP56855BU120 功能描述:數字信號處理器和控制器 - DSP, DSC 120Mhz/120MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*