參數資料
型號: DSPIC30F1010-30I/SP
廠商: Microchip Technology
文件頁數: 28/66頁
文件大小: 0K
描述: IC DSPIC MCU/DSP 6K 28DIP
產品培訓模塊: Asynchronous Stimulus
特色產品: SMPS & Digital Power Conversion Solutions
標準包裝: 15
系列: dsPIC™ 30F
核心處理器: dsPIC
芯體尺寸: 16-位
速度: 30 MIP
連通性: I²C,IrDA,LIN,SPI,UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 21
程序存儲器容量: 6KB(2K x 24)
程序存儲器類型: 閃存
RAM 容量: 256 x 8
電壓 - 電源 (Vcc/Vdd): 3 V ~ 5.5 V
數據轉換器: A/D 6x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 28-DIP(0.300",7.62mm)
包裝: 管件
產品目錄頁面: 650 (CN2011-ZH PDF)
配用: DM300023-ND - KIT DEMO DSPICDEM SMPS BUCK
DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE
dsPIC30F Flash Programming Specification
DS70102K-page 34
2010 Microchip Technology Inc.
11.0 ICSP MODE
11.1
ICSP Mode
ICSP mode is a special programming protocol that
allows you to read and write to the dsPIC30F program-
ming executive. The ICSP mode is the second (and
slower) method used to program the device. This mode
also has the ability to read the contents of executive
memory to determine whether the programming exec-
utive is present. This capability is accomplished by
applying control codes and instructions serially to the
device using pins PGC and PGD.
In ICSP mode, the system clock is taken from the PGC
pin, regardless of the device’s oscillator Configuration
bits. All instructions are first shifted serially into an
internal buffer, then loaded into the Instruction register
and executed. No program fetching occurs from
internal memory. Instructions are fed in 24 bits at a
time. PGD is used to shift data in and PGC is used as
both the serial shift clock and the CPU execution clock.
Data is transmitted on the rising edge and latched on
the falling edge of PGC. For all data transmissions, the
Least Significant bit (LSb) is transmitted first.
11.2
ICSP Operation
Upon entry into ICSP mode, the CPU is idle. Execution
of the CPU is governed by an internal state machine. A
4-bit control code is clocked in using PGC and PGD,
and this control code is used to command the CPU
(see Table 11-1).
The SIX control code is used to send instructions to the
CPU for execution, while the REGOUT control code is
used to read data out of the device via the VISI register.
The operation details of ICSP mode are provided in
TABLE 11-1:
CPU CONTROL CODES IN
ICSP MODE
4-bit
Control
Code
Mnemonic
Description
0000b
SIX
Shift in 24-bit instruction
and execute.
0001b
REGOUT
Shift out the VISI
register.
0010b-1111b N/A
Reserved.
11.2.1
SIX SERIAL INSTRUCTION
EXECUTION
The SIX control code allows execution of dsPIC30F
assembly instructions. When the SIX code is received,
the CPU is suspended for 24 clock cycles as the
instruction is then clocked into the internal buffer. Once
the instruction is shifted in, the state machine allows it
to be executed over the next four clock cycles. While
the received instruction is executed, the state machine
simultaneously shifts in the next 4-bit command (see
Note 1: During ICSP operation, the operating
frequency of PGC must not exceed
5 MHz.
2: Because ICSP is slower, it is recom-
mended that only Enhanced ICSP (E-
ICSP) mode be used for device program-
ming, as described in Section 5.1
Note 1: Coming out of the ICSP entry sequence,
the first 4-bit control code is always
forced to SIX and a forced NOP instruc-
tion is executed by the CPU. Five addi-
tional PGC clocks are needed on start-
up, thereby resulting in a 9-bit SIX com-
mand instead of the normal 4-bit SIX
command. After the forced SIX is clocked
in, ICSP operation resumes as normal
(the next 24 clock cycles load the first
instruction word to the CPU). See
Figure 11-1 for details.
2: TBLRDH, TBLRDL, TBLWTH and TBLWTL
instructions must be followed by a NOP
instruction.
相關PDF資料
PDF描述
PIC24FJ64GB002-I/ML IC MCU 16BIT 64KB FLASH 28QFN
52746-1270 CONN FFC 12POS .5MM R/A ZIF SMD
TS80C31X2-MCE IC MCU 8BIT 40/20MHZ 44-VQFP
52746-0870 CONN FFC 8POS .5MM R/A ZIF SMD
PIC24FJ128GA008-I/PT IC PIC MCU FLASH 128K 80TQFP
相關代理商/技術參數
參數描述
DSPIC30F1010AT-20E/PF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers
DSPIC30F1010AT-20I/PF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers
DSPIC30F1010AT-30I/PF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers
DSPIC30F1010BT-20I/PF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers
DSPIC30F1010BT-30I/PF 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers