- 您現在的位置：買賣IC網 > PDF目錄11442 > DSPIC30F2010-20E/SP (Microchip Technology)IC DSPIC MCU/DSP 12K 28DIP PDF資料下載
參數資料
| 型號： | DSPIC30F2010-20E/SP |
| 廠商： | Microchip Technology |
| 文件頁數： | 31/49頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSPIC MCU/DSP 12K 28DIP |
| 產品培訓模塊： | Asynchronous Stimulus |
| 標準包裝： | 15 |
| 系列： | dsPIC™ 30F |
| 核心處理器： | dsPIC |
| 芯體尺寸： | 16-位 |
| 速度： | 20 MIPS |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 高級欠壓探測/復位，電機控制 PWM，QEI，POR，PWM，WDT |
| 輸入/輸出數： | 20 |
| 程序存儲器容量： | 12KB（4K x 24） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 1K x 8 |
| RAM 容量： | 512 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.5 V ~ 5.5 V |
| 數據轉換器： | A/D 6x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 28-DIP（0.300"，7.62mm） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
2011 Microchip Technology Inc.
DS70118J-page 37
dsPIC30F2010
5.0
INTERRUPTS
The dsPIC30F2010 has 24 interrupt sources and four
processor exceptions (traps), which must be arbitrated
based on a priority scheme.
The CPU is responsible for reading the Interrupt Vec-
tor Table (IVT) and transferring the address contained
in the interrupt vector to the program counter. The
interrupt vector is transferred from the program data
bus into the program counter, via a 24-bit wide
multiplexer on the input of the program counter.
The Interrupt Vector Table (IVT) and Alternate Inter-
rupt Vector Table (AIVT) are placed near the beginning
of program memory (0x000004). The IVT and AIVT
are shown in Figure 5-1.
The
interrupt
controller
is
responsible
for
pre-
processing the interrupts and processor exceptions,
prior to their being presented to the processor core.
The peripheral interrupts and traps are enabled, priori-
tized and controlled using centralized special function
registers:
IFS0<15:0>, IFS1<15:0>, IFS2<15:0>
All interrupt request flags are maintained in these
three registers. The flags are set by their respective
peripherals or external signals, and they are cleared
via software.
IEC0<15:0>, IEC1<15:0>, IEC2<15:0>
All interrupt enable control bits are maintained in
these three registers. These control bits are used to
individually enable interrupts from the peripherals or
external signals.
IPC0<15:0>... IPC11<7:0>
The user-assignable priority level associated with
each of these interrupts is held centrally in these
twelve registers.
IPL<3:0> The current CPU priority level is explicitly
stored in the IPL bits. IPL<3> is present in the
CORCON register, whereas IPL<2:0> are present in
the STATUS Register (SR) in the processor core.
INTCON1<15:0>, INTCON2<15:0>
Global interrupt control functions are derived from
these two registers. INTCON1 contains the control
and status flags for the processor exceptions. The
INTCON2 register controls the external interrupt
request signal behavior and the use of the alternate
vector table.
All interrupt sources can be user-assigned to one of
seven priority levels, 1 through 7, via the IPCx
registers. Each interrupt source is associated with an
interrupt vector, as shown in Figure 5-1. Levels 7 and
1 represent the highest and lowest maskable priorities,
respectively.
If the NSTDIS bit (INTCON1<15>) is set, nesting of
interrupts is prevented. Thus, if an interrupt is currently
being serviced, processing of a new interrupt is
prevented, even if the new interrupt is of higher priority
than the one currently being serviced.
Certain interrupts have specialized control bits for
features like edge or level triggered interrupts, inter-
rupt-on-change, etc. Control of these features remains
within the peripheral module which generates the
interrupt.
The DISI instruction can be used to disable the
processing of interrupts of priorities 6 and lower for a
certain number of instructions, during which the DISI bit
(INTCON2<14>) remains set.
When an interrupt is serviced, the PC is loaded with the
address stored in the vector location in Program Mem-
ory that corresponds to the interrupt. There are 63 dif-
ferent vectors within the IVT (refer to Figure 5-1). These
vectors are contained in locations 0x000004 through
0x0000FE of program memory (refer to Figure 5-1).
These locations contain 24-bit addresses, and in order
to preserve robustness, an address error trap will take
place should the PC attempt to fetch any of these
words during normal execution. This prevents execu-
tion of random data as a result of accidentally decre-
menting a PC into vector space, accidentally mapping
a data space address into vector space or the PC roll-
ing over to 0x000000 after reaching the end of imple-
mented program memory space. Execution of a GOTO
instruction to this vector space will also generate an
address error trap.
Note:
This data sheet summarizes features of
this group of dsPIC30F devices and is not
intended to be a complete reference
source. For more information on the CPU,
peripherals,
register
descriptions
and
general device functionality, refer to the
“dsPIC30F Family Reference Manual”
(DS70046). For more information on the
device instruction set and programming,
refer to the “16-bit MCU and DSC Pro-
grammer’s
Reference
Manual”
(DS70157).
Note:
Interrupt flag bits get set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit. User soft-
ware should ensure the appropriate inter-
rupt flag bits are clear prior to enabling an
interrupt.
Note:
Assigning a priority level of 0 to an inter-
rupt source is equivalent to disabling that
interrupt.
Note:
The IPL bits become read-only whenever
the NSTDIS bit has been set to ‘1’.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC24HJ32GP302T-I/SO | IC PIC MCU FLASH 32K 28SOIC |
| VE-J5D-IW-S | CONVERTER MOD DC/DC 85V 100W |
| VE-J5B-IW-S | CONVERTER MOD DC/DC 95V 100W |
| VE-B6Z-IV | CONVERTER MOD DC/DC 2V 60W |
| VE-B6M-IX-S | CONVERTER MOD DC/DC 10V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| dsPIC30F2010-20I/MM | 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU DSP 28LD 20MIPS 12KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F2010-20I/MMG | 功能描述:數字信號處理器和控制器 - DSP, DSC 16 Bit MCU/DSP 28LD 20M 12KB FL RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F2010-20I/SO | 功能描述:數字信號處理器和控制器 - DSP, DSC 20MHz 12KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F2010-20I/SOG | 功能描述:數字信號處理器和控制器 - DSP, DSC 16bit Signal Cntrlr RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F2010-20I/SP | 功能描述:數字信號處理器和控制器 - DSP, DSC 20MHz 12KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。