參數資料
型號: DSPIC30F3014-30I/ML
廠商: Microchip Technology
文件頁數: 17/153頁
文件大小: 0K
描述: IC DSPIC MCU/DSP 24K 44QFN
產品培訓模塊: Serial Communications using dsPIC30F I2C
Serial Communications using dsPIC30F SPI
Serial Communications using dsPIC30F UART
dsPIC30F 12 bit ADC - Part 2
dsPIC30F Addressing Modes - Part 1
dsPIC30F Architecture - Part 1
dsPIC30F DSP Engine & ALU
dsPIC30F Interrupts
dsPIC30F Motor Control PWM
dsPIC Timers
Asynchronous Stimulus
dsPIC30F Addressing Modes - Part 2
dsPIC30F Architecture - Part 2
dsPIC30F 12-bit ADC Part 1
標準包裝: 45
系列: dsPIC™ 30F
核心處理器: dsPIC
芯體尺寸: 16-位
速度: 30 MIP
連通性: I²C,SPI,UART/USART
外圍設備: 欠壓檢測/復位,POR,PWM,WDT
輸入/輸出數: 30
程序存儲器容量: 24KB(8K x 24)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 1K x 8
RAM 容量: 2K x 8
電壓 - 電源 (Vcc/Vdd): 2.5 V ~ 5.5 V
數據轉換器: A/D 13x12b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 44-VQFN 裸露焊盤
包裝: 管件
產品目錄頁面: 651 (CN2011-ZH PDF)
配用: XLT44QFN2-ND - SOCKET TRAN ICE 44QFN/40DIP
AC164322-ND - MODULE SOCKET MPLAB PM3 28/44QFN
DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE
其它名稱: DSPIC30F301430IML
2010 Microchip Technology Inc.
DS70138G-page 113
dsPIC30F3014/4013
17.3
Modes of Operation
The CAN module can operate in one of several operation
modes selected by the user. These modes include:
Initialization mode
Disable mode
Normal Operation mode
Listen Only mode
Loopback mode
Error Recognition mode
Modes are requested by setting the REQOP<2:0> bits
(CiCTRL<10:8>). Entry into a mode is Acknowledged
by monitoring the OPMODE<2:0> bits (CiCTRL<7:5>).
The module does not change the mode and the
OPMODE bits until a change in mode is acceptable,
generally during bus Idle time which is defined as at
least 11 consecutive recessive bits.
17.3.1
INITIALIZATION MODE
In the Initialization mode, the module does not transmit
or receive. The error counters are cleared and the inter-
rupt flags remain unchanged. The programmer has
access to Configuration registers that are access
restricted in other modes. The module protects the user
from accidentally violating the CAN protocol through
programming errors. All registers that control the con-
figuration of the module can not be modified while the
module is on-line. The CAN module is not allowed to
enter the Configuration mode while a transmission is
taking place. The Configuration mode serves as a lock
to protect the following registers.
All Module Control registers
Baud Rate and Interrupt Configuration registers
Bus Timing registers
Identifier Acceptance Filter registers
Identifier Acceptance Mask registers
17.3.2
DISABLE MODE
In Disable mode, the module does not transmit or
receive. The module has the ability to set the WAKIF bit
due to bus activity, however, any pending interrupts
remain and the error counters retain their value.
If the REQOP<2:0> bits (CiCTRL<10:8>) = 001, the
module enters the Module Disable mode. If the module is
active, the module waits for 11 recessive bits on the CAN
bus, detects that condition as an Idle bus, and then
accepts the module disable command. When the
OPMODE<2:0>
bits
(CiCTRL<7:5>) = 001,
that
indicates whether the module successfully went into
Module Disable mode. The I/O pins revert to normal I/O
function when the module is in the Module Disable mode.
The module can be programmed to apply a low-pass
filter function to the CiRX input line while the module or
the CPU is in Sleep mode. The WAKFIL bit
(CiCFG2<14>) enables or disables the filter.
17.3.3
NORMAL OPERATION MODE
Normal
Operating
mode
is
selected
when
REQOP<2:0> = 000. In this mode, the module is acti-
vated and the I/O pins assume the CAN bus functions.
The
module
transmits
and
receives
CAN
bus
messages via the CxTX and CxRX pins.
17.3.4
LISTEN ONLY MODE
If the Listen Only mode is activated, the module on the
CAN bus is passive. The transmitter buffers revert to
the port I/O function. The receive pins remain inputs.
For the receiver, no error flags or Acknowledge signals
are sent. The error counters are deactivated in this
state. The Listen Only mode can be used for detecting
the baud rate on the CAN bus. To use this, it is neces-
sary that there are at least two further nodes that
communicate with each other.
17.3.5
LISTEN ALL MESSAGES MODE
The module can be set to ignore all errors and receive
any message. The Listen All Messages mode is acti-
vated by setting the REQOP<2:0> bits to ‘111’. In this
mode, the data which is in the message assembly buf-
fer until the time an error occurred, is copied in the
receive buffer and can be read via the CPU interface.
17.3.6
LOOPBACK MODE
If the Loopback mode is activated, the module
connects the internal transmit signal to the internal
receive signal at the module boundary. The transmit
and receive pins revert to their port I/O function.
Note:
Typically, if the CAN module is allowed to
transmit in a particular mode of operation
and a transmission is requested immedi-
ately after the CAN module has been
placed in that mode of operation, the mod-
ule waits for 11 consecutive recessive bits
on the bus before starting transmission. If
the user switches to Disable mode within
this 11-bit period, then this transmission is
aborted and the corresponding TXABT bit
is set and TXREQ bit is cleared.
相關PDF資料
PDF描述
ATMEGA168V-10MI IC AVR MCU 16K 10MHZ 32-QFN
PIC16F873A-I/SO IC MCU FLASH 4KX14 EE 28SOIC
PIC16F873A-I/SP IC MCU FLASH 4KX14 EE 28DIP
PIC32MX320F032H-40V/PT IC MCU 32BIT 32KB FLASH 64TQFP
ATMEGA3290-16AI IC AVR MCU 32K 16MHZ 100TQFP
相關代理商/技術參數
參數描述
dsPIC30F3014T-20E/ML 功能描述:數字信號處理器和控制器 - DSP, DSC 44LD 20MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC30F3014T-20E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 20MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F3014T-20I/ML 功能描述:IC DSPIC MCU/DSP 24K 44QFN RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:dsPIC™ 30F 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C,SPI,UART/USART,USB 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:14 程序存儲器容量:8KB(4K x 16) 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP(0.300",7.62mm) 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
DSPIC30F3014T-20I/PT 功能描述:IC DSPIC MCU/DSP 24K 44TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:dsPIC™ 30F 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C,SPI,UART/USART,USB 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:14 程序存儲器容量:8KB(4K x 16) 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP(0.300",7.62mm) 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
dsPIC30F3014T-30I/ML 功能描述:數字信號處理器和控制器 - DSP, DSC 44LD 30MIPS 24 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT