參數資料
型號: DSPIC30F6013A-20I/PT
廠商: Microchip Technology
文件頁數: 56/66頁
文件大小: 0K
描述: IC DSPIC MCU/DSP 132K 80TQFP
標準包裝: 119
系列: dsPIC™ 30F
核心處理器: dsPIC
芯體尺寸: 16-位
速度: 20 MIPS
連通性: CAN,I²C,SPI,UART/USART
外圍設備: 欠壓檢測/復位,LVD,POR,PWM,WDT
輸入/輸出數: 68
程序存儲器容量: 132KB(44K x 24)
程序存儲器類型: 閃存
EEPROM 大?。?/td> 2K x 8
RAM 容量: 6K x 8
電壓 - 電源 (Vcc/Vdd): 2.5 V ~ 5.5 V
數據轉換器: A/D 16x12b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 80-TQFP
包裝: 托盤
配用: DM300024-ND - KIT DEMO DSPICDEM 1.1
XLT80PT3-ND - SOCKET TRAN ICE 80MQFP/TQFP
AC164320-ND - MODULE SKT MPLAB PM3 80TQFP
AC30F007-ND - MODULE SKT FOR DSPIC30F 80TQFP
其它名稱: DSPIC30F6013A20IP
dsPIC30F Flash Programming Specification
DS70102K-page 6
2010 Microchip Technology Inc.
5.2
Entering Enhanced ICSP Mode
The Enhanced ICSP mode is entered by holding PGC
and PGD high, and then raising MCLR/VPP to VIHH
(high voltage), as illustrated in Figure 5-2. In this mode,
the code memory, data EEPROM and Configuration
bits can be efficiently programmed using the program-
ming executive commands that are serially transferred
using PGC and PGD.
FIGURE 5-2:
ENTERING ENHANCED
ICSP MODE
5.3
Chip Erase
Before a chip can be programmed, it must be erased.
The Bulk Erase command (ERASEB) is used to perform
this task. Executing this command with the MS
command field set to 0x3 erases all code memory, data
EEPROM and code-protect Configuration bits. The
Chip Erase process sets all bits in these three memory
regions to ‘1’.
Since non-code-protect Configuration bits cannot be
erased, they must be manually set to ‘1’ using multiple
PROGC commands. One PROGC command must be
sent for each Configuration register (see Section 5.7
If Advanced Security features are enabled, then indi-
vidual Segment Erase operations would need to be
performed, depending on which segment needs to be
programmed at a given stage of system programming.
The user should have the flexibility to select specific
segments for programming.
Note:
The Device ID registers cannot be erased.
These registers remain intact after a Chip
Erase is performed.
5.4
Blank Check
The term “Blank Check” means to verify that the device
has been successfully erased and has no programmed
memory cells. A blank or erased memory cell reads as
‘1’. The following memories must be blank checked:
All implemented code memory
All implemented data EEPROM
All Configuration bits (for their default value)
The Device ID registers (0xFF0000:0xFF0002) can be
ignored by the Blank Check since this region stores
device information that cannot be erased. Additionally,
all unimplemented memory space should be ignored
from the Blank Check.
The QBLANK command is used for the Blank Check. It
determines if the code memory and data EEPROM are
erased by testing these memory regions. A ‘BLANK’ or
‘NOT BLANK’ response is returned. The READD
command is used to read the Configuration registers. If
it is determined that the device is not blank, it must be
erased (see Section 5.3 “Chip Erase”) before
attempting to program the chip.
Note 1: The sequence that places the device into
Enhanced ICSP mode places all unused
I/Os in the high-impedance state.
2: Before entering Enhanced ICSP mode,
clock switching must be disabled using
ICSP, by programming the FCKSM<1:0>
bits in the FOSC Configuration register to
‘11’ or ‘10’.
3: When in Enhanced ICSP mode, the SPI
output pin (SDO1) will toggle while the
device is being programmed.
MCLR/VPP
P7
PGD
PGD = Input
PGC
VDD
VIHH
P6
相關PDF資料
PDF描述
DSPIC30F6012A-20I/PT IC DSPIC MCU/DSP 144K 64TQFP
DSPIC30F6011A-20I/PT IC DSPIC MCU/DSP 132K 64TQFP
DSPIC30F6010A-20I/PT IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F5016-20I/PT IC DSPIC MCU/DSP 66K 80TQFP
PIC16LF1526-I/PT MCU PIC 14KB FLASH 64TQFP
相關代理商/技術參數
參數描述
dsPIC30F6013A-30I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 30MIPS 132 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC30F6013A-30I/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 30MIPS 132 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6013AT-20E/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 16-bit MCU/DSP 30MIPS 132KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC30F6013AT-20E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 20MIPS 132 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6013AT-20I/PT 功能描述:IC DSPIC MCU/DSP 132K 80TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:dsPIC™ 30F 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C,SPI,UART/USART,USB 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:14 程序存儲器容量:8KB(4K x 16) 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP(0.300",7.62mm) 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP