參數資料
型號: DSPIC30F6015-20I/PT
廠商: Microchip Technology
文件頁數: 1/66頁
文件大?。?/td> 0K
描述: IC DSPIC MCU/DSP 144K 64TQFP
標準包裝: 160
系列: dsPIC™ 30F
核心處理器: dsPIC
芯體尺寸: 16-位
速度: 20 MIPS
連通性: CAN,I²C,SPI,UART/USART
外圍設備: 高級欠壓探測/復位,LVD,電機控制 PWM,QEI,POR,PWM,WDT
輸入/輸出數: 52
程序存儲器容量: 144KB(48K x 24)
程序存儲器類型: 閃存
EEPROM 大小: 4K x 8
RAM 容量: 8K x 8
電壓 - 電源 (Vcc/Vdd): 2.5 V ~ 5.5 V
數據轉換器: A/D 16x10b
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 64-TQFP
包裝: 托盤
配用: AC164315-ND - MODULE SKT MPLAB PM3 44TQFP
其它名稱: DSPIC30F601520IPT
2010 Microchip Technology Inc.
DS70102K-page 1
dsPIC30F
1.0
OVERVIEW AND SCOPE
This document defines the programming specification
for the dsPIC30F family of Digital Signal Controllers
(DSCs). The programming specification is required
only for the developers of third-party tools that are used
to program dsPIC30F devices. Customers using
dsPIC30F devices should use development tools that
already provide support for device programming.
This document includes programming specifications
for the following devices:
dsPIC30F2010/2011/2012
dsPIC30F3010/3011/3012/3013/ 3014
dsPIC30F4011/4012/4013
dsPIC30F5011/5013/5015/5016
dsPIC30F6010/6011/6012/6013/6014/6015
dsPIC30F6010A/6011A/6012A/6013A/6014A
2.0
PROGRAMMING OVERVIEW
OF THE dsPIC30F
The dsPIC30F family of DSCs contains a region of on-
chip memory used to simplify device programming.
This region of memory can store a programming
executive, which allows the dsPIC30F to be
programmed faster than the traditional means. Once
the programming executive is stored to memory by an
external programmer (such as Microchip’s MPLAB
ICD 2, MPLAB PM3, PRO MATE II, or MPLAB REAL
ICE), it can then interact with the external
programmer to efficiently program devices.
The programmer and programming executive have a
master-slave relationship, where the programmer is
the master programming device and the programming
executive is the slave, as illustrated in Figure 2-1.
FIGURE 2-1:
OVERVIEW OF dsPIC30F
PROGRAMMING
Two different methods are used to program the chip in
the user’s system. One method uses the Enhanced In-
Circuit Serial Programming (Enhanced ICSP)
protocol and works with the programming executive.
The other method uses In-Circuit Serial Programming
(ICSP) protocol and does not use the programming
executive.
The Enhanced ICSP protocol uses the faster, high-
voltage method that takes advantage of the
programming executive. The programming executive
provides all the necessary functionality to erase,
program and verify the chip through a small command
set. The command set allows the programmer to
program the dsPIC30F without having to deal with the
low-level programming protocols of the chip.
The ICSP programming method does not use the
programming executive. It provides native, low-level
programming capability to erase, program and verify
the chip. This method is significantly slower because it
uses control codes to serially execute instructions on
the dsPIC30F device.
This specification describes the ICSP and Enhanced
ICSP
programming
methods.
the
programming
executive
application
and
application programmer’s interface for the host
programmer.
describes the ICSP programming method.
2.1
Hardware Requirements
In ICSP or Enhanced ICSP mode, the dsPIC30F
requires two programmable power supplies: one for
VDD and one for MCLR. For Bulk Erase programming,
which is required for erasing code protection bits, VDD
must be greater than 4.5 volts. Refer to Section 13.0
for additional hardware parameters.
Programmer
dsPIC30F Device
Programming
Executive
On-chip Memory
2
dsPIC30F Flash Programming Specification
相關PDF資料
PDF描述
DSPIC30F6014A-20I/PT IC DSPIC MCU/DSP 144K 80TQFP
DSPIC30F6013A-20I/PT IC DSPIC MCU/DSP 132K 80TQFP
DSPIC30F6012A-20I/PT IC DSPIC MCU/DSP 144K 64TQFP
DSPIC30F6011A-20I/PT IC DSPIC MCU/DSP 132K 64TQFP
DSPIC30F6010A-20I/PT IC DSPIC MCU/DSP 144K 80TQFP
相關代理商/技術參數
參數描述
dsPIC30F6015-30I/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 30MIPS 144 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC30F6015T-20E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 20MIPS 144 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC30F6015T-20I/PT 功能描述:IC DSPIC MCU/DSP 144K 64TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:dsPIC™ 30F 產品培訓模塊:XLP Deep Sleep Mode 8-bit PIC® Microcontroller Portfolio 標準包裝:22 系列:PIC® XLP™ 18F 核心處理器:PIC 芯體尺寸:8-位 速度:48MHz 連通性:I²C,SPI,UART/USART,USB 外圍設備:欠壓檢測/復位,POR,PWM,WDT 輸入/輸出數:14 程序存儲器容量:8KB(4K x 16) 程序存儲器類型:閃存 EEPROM 大小:256 x 8 RAM 容量:512 x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 5.5 V 數據轉換器:A/D 11x10b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:20-DIP(0.300",7.62mm) 包裝:管件 產品目錄頁面:642 (CN2011-ZH PDF) 配用:DV164126-ND - KIT DEVELOPMENT USB W/PICKIT 2DM164127-ND - KIT DEVELOPMENT USB 18F14/13K50AC164112-ND - VOLTAGE LIMITER MPLAB ICD2 VPP
DSPIC30F6015T-30E/PT 制造商:Microchip Technology Inc 功能描述:DGTL SGNL CNTRLRS 64TQFP - Tape and Reel
dsPIC30F6015T-30I/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 30MIPS 144 KB RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT