參數資料
型號： DSPIC33FJ32MC202-E/MM
廠商： Microchip Technology
文件頁數： 44/76頁
文件大?。?/td> 0K
描述： IC DSPIC MCU/DSP 32K 28QFN
產品培訓模塊： Asynchronous Stimulus
特色產品： PIC24FJ/33FJ MCUs & dsPIC? DSCs
標準包裝： 61
系列： dsPIC™ 33F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 40 MIP
連通性： I²C，IrDA，LIN，SPI，UART/USART
外圍設備： 欠壓檢測/復位，DMA，電機控制 PWM，QEI，POR，PWM，WDT
輸入/輸出數： 21
程序存儲器容量： 32KB（32K x 8）
程序存儲器類型： 閃存
RAM 容量： 2K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 6x10b/12b
振蕩器型： 內部
工作溫度： -40°C ~ 125°C
封裝/外殼： 28-VQFN 裸露焊盤
包裝： 管件
產品目錄頁面： 652 (CN2011-ZH PDF)
配用： AC164336-ND - MODULE SOCKET FOR PM3 28/44QFN
DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
DM240001-ND - BOARD DEMO PIC24/DSPIC33/PIC32
2007-2012 Microchip Technology Inc.
DS70283K-page 49
dsPIC33FJ32MC202/204 and dsPIC33FJ16MC304
4.6.3
MODULO ADDRESSING
APPLICABILITY
Modulo Addressing can be applied to the Effective
Address (EA) calculation associated with any W
register. Address boundaries check for addresses
equal to:
The upper boundary addresses for incrementing
buffers
The lower boundary addresses for decrementing
buffers
It is important to realize that the address boundaries
check for addresses less than or greater than the upper
(for incrementing buffers) and lower (for decrementing
buffers) boundary addresses (not just equal to).
Address changes can, therefore, jump beyond
boundaries and still be adjusted correctly.
4.7
Bit-Reversed Addressing
Bit-Reversed Addressing mode is intended to simplify
data re-ordering for radix-2 FFT algorithms. It is
supported by the X AGU for data writes only.
The modifier, which can be a constant value or register
contents, is regarded as having its bit order reversed. The
address source and destination are kept in normal order.
Thus, the only operand requiring reversal is the modifier.
4.7.1
BIT-REVERSED ADDRESSING
IMPLEMENTATION
Bit-Reversed Addressing mode is enabled in any of
these situations:
BWM bits (W register selection) in the MODCON
register are any value other than ‘15’ (the stack
cannot be accessed using Bit-Reversed
Addressing)
The BREN bit is set in the XBREV register
The addressing mode used is Register Indirect
with Pre-Increment or Post-Increment
If the length of a bit-reversed buffer is M = 2N bytes,
the last ‘N’ bits of the data buffer start address must
be zeros.
XB<14:0> is the Bit-Reversed Address modifier, or
‘pivot point’, which is typically a constant. In the case of
an FFT computation, its value is equal to half of the FFT
data buffer size.
When enabled, Bit-Reversed Addressing is executed
only for Register Indirect with Pre-Increment or
Post-Increment Addressing and word-sized data
writes. It will not function for any other addressing
mode or for byte-sized data, and normal addresses are
generated instead. When Bit-Reversed Addressing is
active, the W Address Pointer is always added to the
address modifier (XB), and the offset associated with
the Register Indirect Addressing mode is ignored. In
addition, as word-sized data is a requirement, the LSb
of the EA is ignored (and always clear).
If Bit-Reversed Addressing has already been enabled
by setting the BREN bit (XBREV<15>), a write to the
XBREV register should not be immediately followed by
an indirect read operation using the W register that has
been designated as the bit-reversed pointer.
Note:
The modulo corrected effective address is
written back to the register only when
Pre-Modify or Post-Modify Addressing
mode is used to compute the effective
address. When an address offset (such as
[W7 + W2]) is used, Modulo Address
correction is performed but the contents of
the register remain unchanged.
Note:
All bit-reversed EA calculations assume
word-sized data (LSb of every EA is
always clear). The XB value is scaled
accordingly to generate compatible (byte)
addresses.
Note:
Modulo Addressing and Bit-Reversed
Addressing
should
not
be
enabled
together. If an application attempts to do
so, Bit-Reversed Addressing will assume
priority when active for the X WAGU and X
WAGU,
Modulo
Addressing
will
be
disabled. However, Modulo Addressing will
continue to function in the X RAGU.
相關PDF資料
PDF描述
DSPIC33FJ64MC710-I/PF IC DSPIC MCU/DSP 64K 100TQFP
EFM32G200F64 MCU 32BIT 64KB FLASH 32-QFN
EFM32G210F128 IC MCU 32BIT 128KB FLASH 32QFN
EFM32G222F64 IC MCU 32BIT 64KB FLASH QFP48
EFM32G230F128 IC MCU 32BIT 128KB FLASH 64QFN
相關代理商/技術參數
參數描述
dsPIC33FJ32MC202-H/MM 功能描述:數字信號處理器和控制器 - DSP, DSC 16-bit 32KB Flash 40 MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ32MC202-H/SO 功能描述:數字信號處理器和控制器 - DSP, DSC 16-bit 32KB Flash 40 MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ32MC202-I/MM 功能描述:數字信號處理器和控制器 - DSP, DSC 16B DSC 28LD 32KB FlashMotor40 RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPIC33FJ32MC202-I/MM 制造商:Microchip Technology Inc 功能描述:16 bit DSC 28LD 32KB Flash Motor 40 MIPS
DSPIC33FJ32MC202-I/MM 制造商:Microchip Technology Inc 功能描述:DSC 16BIT 32K FLASH 40MIPS 28QFN-S 制造商:Microchip Technology Inc 功能描述:DSC, 16BIT, 32K FLASH, 40MIPS, 28QFN-S
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*