- 您現在的位置：買賣IC網 > PDF目錄299014 > E-L6917BD (STMICROELECTRONICS) SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO28 PDF資料下載
參數資料
| 型號： | E-L6917BD |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, 600 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | ROHS COMPLIANT, SO-28 |
| 文件頁數： | 30/33頁 |
| 文件大?。?/td> | 465K |
| 代理商： | E-L6917BD |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁
L6917B
6/33
PIN FUNCTION
N
Name
Description
1
LGATE1
Channel 1 low side gate driver output.
2
VCCDR
Mosfet driver supply. It can be varied from 5V to 12V.
3
PHASE1 This pin is connected to the source of the upper mosfet and provides the return path for the high
side driver of channel 1.
4
UGATE1 Channel 1 high side gate driver output.
5
BOOT1
Channel 1 bootstrap capacitor pin. Through this pin is supplied the high side driver and the upper
mosfet. Connect through a capacitor to the PHASE1 pin and through a diode to Vcc (cathode vs.
boot).
6
VCC
Device supply voltage. The operative supply voltage is 12V.
7
GND
All the internal references are referred to this pin. Connect it to the PCB signal ground.
8
COMP
This pin is connected to the error amplifier output and is used to compensate the control
feedback loop.
9
FB
This pin is connected to the error amplifier inverting input and is used to compensate the voltage
control feedback loop.
A current proportional to the sum of the current sensed in both channel is sourced from this pin
(50
A at full load, 70A at the Over Current threshold). Connecting a resistor between this pin
and VSEN pin allows programming the droop effect.
10
VSEN
Connected to the output voltage it is able to manage Over & Under-voltage conditions and the
PGOOD signal. It is internally connected with the output of the Remote Sense Buffer for Remote
Sense of the regulated voltage.
If no Remote Sense is implemented, connect it directly to the regulated voltage in order to
manage OVP, UVP and PGOOD.
11
FBR
Remote sense buffer non-inverting input. It has to be connected to the positive side of the load to
perform a remote sense.
If no remote sense is implemented, connect directly to the output voltage (in this case connect
also the VSEN pin directly to the output regulated voltage).
12
FBG
Remote sense buffer inverting input. It has to be connected to the negative side of the load to
perform a remote sense.
Pull-down to ground if no remote sense is implemented.
13
ISEN1
Channel 1 current sense pin. The output current may be sensed across a sense resistor or
across the low-side mosfet RdsON. This pin has to be connected to the low-side mosfet drain or
to the sense resistor through a resistor Rg in order to program the positive current limit at 140%
as follow:
Where 35
A is the current offset information relative to the Over Current condition (offset at OC
threshold minus offset at zero load).
The net connecting the pin to the sense point must be routed as close as possible to the
PGNDS1 net in order to couple in common mode any picked-up noise.
14
PGNDS1
Channel 1 Power Ground sense pin. The net connecting the pin to the sense point (*) must be
routed as close as possible to the ISEN1 net in order to couple in common mode any picked-up
noise.
15
PGNDS2
Channel 2 Power Ground sense pin. The net connecting the pin to the sense point (*) must be
routed as close as possible to the ISEN2 net in order to couple in common mode any picked-up
noise.
I
MAX
35
AR
g
R
se nse
--------------------------
=
(*) Through a resistor Rg.
相關PDF資料 |
PDF描述 |
|---|---|
| E-L8150TR | BRUSHLESS DC MOTOR CONTROLLER, PDSO28 |
| E-L9935013TR | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO20 |
| E1L33-3BOA6-02 | T-1 SINGLE COLOR LED, BLUE, 3 mm |
| E1L35-3G0A7-02 | T-1 SINGLE COLOR LED, GREEN, 3 mm |
| E1L35-3G0A5-02 | T-1 SINGLE COLOR LED, GREEN, 3 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| E-L6917BDTR | 功能描述:DC/DC 開關控制器 Prog Dual-Phase Cont RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| E-L6919E | 功能描述:電流型 PWM 控制器 5-Bit Dual Ph Contlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| E-L6919ETR | 功能描述:電流型 PWM 控制器 5-Bit Dual Ph Contlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| E-L6920D | 功能描述:直流/直流開關轉換器 0.6 to 5.5V Step-Up RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| E-L6920DTR | 功能描述:直流/直流開關轉換器 0.6 to 5.5V Step-Up RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。