- 您現在的位置：買賣IC網 > PDF目錄362580 > E28F200BX-T80 (INTEL CORP) 2-MBIT (128K x 16, 256K x 8) BOOT BLOCK FLASH MEMORY FAMILY PDF資料下載
參數資料
| 型號： | E28F200BX-T80 |
| 廠商： | INTEL CORP |
| 元件分類： | PROM |
| 英文描述： | 2-MBIT (128K x 16, 256K x 8) BOOT BLOCK FLASH MEMORY FAMILY |
| 中文描述： | 128K X 16 FLASH 12V PROM, 80 ns, PDSO56 |
| 封裝： | 20 X 14 MM, TSOP-56 |
| 文件頁數： | 12/55頁 |
| 文件大?。?/td> | 636K |
| 代理商： | E28F200BX-T80 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
2-MBIT SmartVoltage BOOT BLOCK FAMILY
E
12
SEE NEW DESIGN RECOMMENDATIONS
Table 2. 28F200/002 Pin Descriptions
Symbol
Type
Name and Function
WP#
INPUT
WRITE PROTECT:
Provides a method for unlocking the boot block in a system
without a 12 V supply.
When WP# is at logic low, the boot block is locked
, preventing program and
erase operations to the boot block. If a program or erase operation is attempted
on the boot block when WP# is low, the corresponding status bit (bit 4 for
program, bit 5 for erase) will be set in the status register to indicate the operation
failed.
When WP# is at logic high, the boot block is unlocked
and can be
programmed or erased.
NOTE:
This feature is overridden and the boot block unlocked when RP# is at
V
HH
. See Section 3.4 for details on write protection.
BYTE#
INPUT
BYTE# ENABLE:
Not available on
28F002B
. Controls whether the device
operates in the byte-wide mode (x8) or the word-wide mode (x16). BYTE# pin
must be controlled at CMOS levels to meet the CMOS current specification in the
standby mode.
When BYTE# is at logic low, the byte-wide mode is enabled
, where data is
read and programmed on DQ
0
–DQ
7
and DQ
15
/A
–1
becomes the lowest order
address that decodes between the upper and lower byte. DQ
8
–DQ
14
are tri-stated
during the byte-wide mode.
When BYTE# is at logic high, the word-wide mode is enabled
, where data is
read and programmed on DQ
0
–DQ
15
.
V
CC
DEVICE POWER SUPPLY:
5.0 V
±
10%, 3.3 V
±
0.3 V, 2.7 V–3.6 V (BE/CE
only)
V
PP
PROGRAM/ERASE POWER SUPPLY:
For erasing memory array blocks or
programming data in each block, a voltage either of 5 V
±
10% or 12 V
±
5% must
be applied to this pin. When V
PP
< V
PPLK
all blocks are locked and protected
against Program and Erase commands.
GND
GROUND:
For all internal circuitry.
NC
NO CONNECT:
Pin may be driven or left floating.
相關PDF資料 |
PDF描述 |
|---|---|
| E28F200CV-T60 | 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| E28F200CV-T80 | 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| E28F200CVT60 | 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| E28F200CVT80 | 2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| E28F200BL-T150 | 2-MBIT (128K x 16, 256K x 8)LOW-POWER BOOT BLOCK FLASH MEMORY FAMILY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| E28F200CVB60 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| E28F200CV-B60 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| E28F200CVB80 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| E28F200CV-B80 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
| E28F200CVT60 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:2-MBIT SmartVoltage BOOT BLOCK FLASH MEMORY FAMILY |
發布緊急采購，3分鐘左右您將得到回復。