- 您現在的位置：買賣IC網 > PDF目錄362592 > E710AHF (Semtech Corporation) 500 MHz Pin Electronics Driver, Window Comparator, and Load PDF資料下載
參數資料
| 型號： | E710AHF |
| 廠商： | Semtech Corporation |
| 英文描述： | 500 MHz Pin Electronics Driver, Window Comparator, and Load |
| 中文描述： | 500兆赫引腳電子驅動器，窗口比較器和負載 |
| 文件頁數： | 6/17頁 |
| 文件大小： | 206K |
| 代理商： | E710AHF |
6
2000 Semtech Corp.
www.semtech.com
EDGE HIGH-PERFORMANCE PRODUCTS
Circuit Description
(continued)
Edge710
Source and Sink Current Levels
The amount of current that the diode bridge can source
and sink is adjustable from 0 mA to 35 mA. The source
and sink levels are separate and independent.
ISC_IN and ISK_IN are current controlled inputs whose
voltage level is held very close to ground (<100 mV
variation) over the entire legal current input range.
There is a nominal gain of 20 between the ISC_IN current
and the bridge source current.
ISOURCE = 20 * ISC_IN
There is a nominal gain of –20 between the ISK_IN current
and the bridge sink current.
ISINK = –20 * ISK_IN
Because the inversion creates a 180 phase shift between
ISK_IN and ISINK, there is a tendency toward instability.
A minimum of 500 W of external series resistance should
be used between an external voltage or current source
and the ISC_IN and ISK_IN pins to ensure stability. Stray
capacitance at the ISK_IN pin should be kept to a
minimum. PCB layout should minimize coupling between
ISK_IN and LOAD.
Caution: The ISKIN and ISCIN inputs are designed for
positive current between 0 mA and 1.75 mA flowing into
the part. Care should be taken to insure that current is
never required to flow out of the part on these two nodes.
Commutating Voltage Compensation
The VCM_CAP pin is an op amp compensation node that
requires a fixed .01
μ
F chip capacitor (with good high
frequency characteristics) to ground. This capacitor is
used to compensate an internal node on the on-chip buffer
for the commutating voltage input.
Split Load
The VCM_OUT_A is the actual commutating voltage
generated by the on-chip buffer. VCM_OUT_A is also
connected to the upper half of the diode bridge, and is
responsible for sinking the programmed source current
when the load is sinking current from the DUT.
VCM_OUT_B is connected to the lower half of the diode
bridge, and is responsible for providing the sink current
when the load is sourcing current to the DUT.
VCM_OUT_B does NOT have an on-chip buffer. To
configure the load as a standard active diode bridge,
connect VCM_OUT_A and VCM_OUT_B together off-chip.
Or, to configure the load as a split load, an external buffer
must be used for VCM_OUT_B.
External Bridge Connections
Access to the top and bottom of the diode bridge is granted
through a 1 KW resistor. Pins BRIDGE_SC and BRIDGE_SK
allow external current sources to be used instead of the
internal I_SOURCE and I_SINK sources. These external
pins are useful when extremely accurate source and sink
currents are required for low current operation.
1K
1K
BRIDGE_SC
I_SOURCE
I_SINK
LOAD
BRIDGE_SK
VCM_OUT_B
VCM_OUT_A
VCM_IN
相關PDF資料 |
PDF描述 |
|---|---|
| E712545 | 8-bit Proprietary Microcontroller |
| E713704 | 16-bit Proprietary Microcontroller |
| E72-12V | Engineering Catalog 169 |
| E72-5V | Engineering Catalog 169 |
| E73-12V | Engineering Catalog 169 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| E710-EDGE710 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:500 MHz Pin Electronics Driver. Window Comparator. and Load |
| E-711064-5-9 | 制造商:TE Connectivity 功能描述:Labels Dot Matrix Printable Label Polyester White 71.1x6.4mm |
| E711274 | 制造商:ELO Touch Solutions 功能描述:1541L FRONT-MOUNT BEZEL KIT 制造商:Elo Touch Solutions Inc 功能描述:ELO-1541L-FRONTMOUNT-BEZ-R - Bulk |
| E71-12V | 制造商:GILWAY 制造商全稱:Gilway Technical Lamp 功能描述:Engineering Catalog 169 |
| E71186-000 | 制造商:TE Connectivity 功能描述:CBL 2CNDCTR 24AWG SILV PLTD CPPR ALLOY OR 600V - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:55PC1124-24-6/9-3 |
發布緊急采購，3分鐘左右您將得到回復。