參數資料
型號: Edge646
廠商: Semtech Corporation
英文描述: Pin Electronics Driver, Window Comparator, and Switch Matrix(用于自動測試設備的引腳電子驅動器,窗式比較器和開關陣列)
中文描述: 引腳電子驅動程序,窗口比較器和開關矩陣(用于自動測試設備的引腳電子驅動器,窗式比較器和開關陣列)
文件頁數: 6/13頁
文件大?。?/td> 135K
代理商: EDGE646
6
2000 Semtech Corp.
www.semtech.com
EDGE HIGH-PERFORMANCE PRODUCTS
Application Information
Edge646
PRELIMINARY
Power Supplies Decoupling
A .1
μ
F capacitor is recommended between VCC and
VEE.
In addition, solid VCC and VEE planes are recommended
to provide a low inductance path for the power supply
currents. These planes will reduce any inductive supply
drops associated with swtiching currents on the power
supply pins. If solid planes are not possible, then wide
power busses are preferable.
VH, VL, and VTT Decoupling
As the VH, VL, and VTT inputs are unbuffered and must
supply the driver output current, decoupling capacitors
for these inputs are recommended in proportion to the
amount of output current the application requires. In
general, a surge current of 50 mA (5V swings series
terminated with 50
into a 50
transmission line) are
the maximum dynamic output currents the driver should
see. The decoupling capacitors should be able to provide
this current for the duration of the round trip time between
the pin electronics and the DUT, and then recharge
themselves before the next such transition would occur.
Once this condition is satisfied, the VH, VL, and VTT supply
voltages are more responsible for establishing the DC levels
associated with each function and recharging the
capacitors, rather than providing the actual dynamic
currents required to drive the DUT transmission line.
Ideally, VH, VL, and VTT would each have a dedicated
power layer on the PC board for the lowest possible
inductance power supply distribution.
Latchup Protection
The Edge646 has several power supply requirements to
protect the part in power supply fault situations, as well
as during power up and power down sequences. VCC
must remain greater than or equal to VDD (external supply
for the digital logic) at all times. Both VCC and VDD must
always be positive (above ground), and VEE must always
be negative (at or below ground).
The three diode configuration shown in Figure 3 should
be used on a once-per-board basis.
Figure 3.
Power Supply Protection Scheme
gure 5.
Warning: It is extremely important that the voltage on any
device pin does not exceed the range of VEE –0.5V to VCC
+0.5V at any time, either during power up, normal
operation, or during power down. Failure to adhere to this
requirement could result in latchup of the device, which
could be destructive if the system power supplies are
capable of supplying large amounts of current. Even if the
device is not immediately destroyed, the cumulative
damage caused by the stress of repeated latchup may
affect device reliability.
VCC
VDD
VEE
1N5820 or
Equivalent
相關PDF資料
PDF描述
Edge647 Pin Electronics Driver, Window Comparator, and Switch Matrix(用于自動測試設備的引腳電子驅動器,窗式比較器和開關陣列)
Edge649 Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????)
Edge692 Connector
Edge693 500 MHz Monolithic Dual Pin Electronics Driver
Edge710 500 MHz Pin Electronics Driver, Window Comparator, and Load
相關代理商/技術參數
參數描述
EDGE647 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Pin Electronics Driver, Window Comparator, and Switch Matrix
EDGE649 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Octal Pin Electronics Driver/Receiver
EDGE692 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:200 MHz Monolithic Dual Pin Electronics Driver
EDGE693 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:500 MHz Monolithic Dual Pin Electronics Driver
EDGE710 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:500 MHz Pin Electronics Driver, Window Comparator, and Load