- 您現在的位置：買賣IC網 > PDF目錄97896 > EKK8011 Low-Voltage, Single Supply, SPST, High Performance Analog Switches; Temperature Range: -40°C to 85°C; Package: 8-SOIC T&R PDF資料下載
參數資料
| 型號： | EKK8011 |
| 英文描述： | Low-Voltage, Single Supply, SPST, High Performance Analog Switches; Temperature Range: -40°C to 85°C; Package: 8-SOIC T&R |
| 中文描述： | 的USB PS / 2鍵盤控制器 |
| 文件頁數： | 10/24頁 |
| 文件大?。?/td> | 465K |
| 代理商： | EKK8011 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
MAX5942A/MAX5942B
IEEE 802.3af Power-Over-Ethernet
Interface/PWM Controller for Power Devices
18
______________________________________________________________________________________
PWM Comparator and Slope Compensation
An internal 275kHz oscillator determines the switching
frequency of the controller. At the beginning of each
cycle, NDRV switches the N-channel MOSFET on.
NDRV switches the external MOSFET off after the maxi-
mum duty cycle has been reached, regardless of the
feedback.
The MAX5942B uses an internal ramp generator for
slope compensation. The internal ramp signal is reset
at the beginning of each cycle and slews at 26mV/s.
The PWM comparator uses the instantaneous current,
the error voltage, the internal reference, and the slope
compensation (MAX5942A only) to determine when to
switch the N-channel MOSFET off. In normal operation,
the N-channel MOSFET turns off when:
where IPRIMARY is the current through the N-channel
MOSFET, VREF is the 2.4V internal reference, VEA is the
output voltage of the internal amplifier, and VSCOMP is a
ramp function starting at zero and slewing at 26mV/s
(MAX5942A only). When using the MAX5942A in a for-
ward-converter configuration, the following condition
must be met to avoid control-loop subharmonic oscilla-
tions:
where k = 0.75 to 1, and NS and NP are the number of
turns on the secondary and primary side of the trans-
former, respectively. L is the output filter inductor. This
makes the output inductor current downslope as refer-
enced across RSENSE equal to the slope compensa-
tion. The controller responds to transients within one
cycle when this condition is met.
N-Channel MOSFET Gate Driver
NDRV drives an N-channel MOSFET. NDRV sources
and sinks large transient currents to charge and dis-
charge the MOSFET gate. To support such switching
transients, bypass VCC with a ceramic capacitor. The
average current as a result of switching the MOSFET is
the product of the total gate charge and the operating
frequency. It is this current plus the DC quiescent cur-
rent that determines the total operating current.
Applications Information
Design Example
The following is a general procedure for designing a
forward converter using the MAX5942B:
1) Determine the requirements.
2) Set the output voltage.
3) Calculate the transformer primary to secondary
winding turns ratio.
4) Calculate the reset to primary winding turns ratio.
5) Calculate the tertiary to primary winding turns
ratio.
6) Calculate the current-sense resistor value.
7) Calculate the output inductor value.
8) Select the output capacitor.
The circuit in Figure 5 was designed as follows:
1) 30V
≤ VIN ≤ 67V, VOUT = 5V, IOUT = 10A, VRIPPLE ≤
50mV. Turn-on threshold is set at 38.6V.
2) To set the output voltage, calculate the values of
resistors R1 and R2 according to the following
equation:
where VREF is the reference voltage of the shunt reg-
ulator, and R1 and R2 are the resistors shown in
Figures 5 and 6.
3) The turns ratio of the transformer is calculated based
on the minimum input voltage and the lower limit of
the maximum duty cycle for the MAX5942B (44%).
To enable the use of MOSFETs with drain-source
breakdown voltages of less than 200V, use the
MAX5942B with the 50% maximum duty cycle.
Calculate the turns ratio according to the following
equation:
where:
NS/NP = Turns ratio (NS is the number of secondary
turns and NP is the number of primary turns).
N
VV
D
DV
S
P
OUT
D1
MAX
IN_MIN
≥
+×
()
×
VV
R
RR
k
VV
V
OUT
REF
SS SHDN
=+
<<
==
1
2
12
50
24
//
.
_
N
kR
V
S
P
SENSE
OUT
× ××
=
L
mV s
26
/
IR
V
- V
PRIMARY
SENSE
EA
REF
SCOMP
×>
相關PDF資料 |
PDF描述 |
|---|---|
| EKK8301 | Low-Voltage, Single Supply, SPST, High Performance Analog Switches; Temperature Range: -40°C to 85°C; Package: 8-SOIC T&R |
| EKM6211 | Ultra Low ON-Resistance, Single Supply, Dual SPST Analog Switches; Temperature Range: -40°C to 85°C; Package: 8-MSOP |
| EKM8003 | Ultra Low ON-Resistance, Single Supply, Dual SPST Analog Switches; Temperature Range: -40°C to 85°C; Package: 8-MSOP T&R |
| EKM8021 | Ultra Low ON-Resistance, Single Supply, Dual SPST Analog Switches; Temperature Range: -40°C to 85°C; Package: 8-MSOP T&R |
| EKM8022 | Ultra Low ON-Resistance, +1.1V to +4.5V Single Supply, SPDT Analog Switch; Temperature Range: -40°C to 85°C; Package: 6-SC-70 T&R |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EKK8011AB | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:USB & PS/2 Keyboard Encoder |
| EKK8301 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PS/2 keyboard controller |
| EKK-EVALBOT | 功能描述:開發板和工具包 - ARM Keil Stellaris Eval Robot RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| EKK-LM3S1968 | 功能描述:開發板和工具包 - ARM Stellaris Eval Kit w/ ARM/Keil Tools RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V |
| EKK-LM3S1968 | 制造商:Texas Instruments 功能描述:LM3S1968 MCU Eval Kit w/ Keil RealView M |
發布緊急采購，3分鐘左右您將得到回復。