參數資料
型號： EL1503ACL
廠商： Intersil
文件頁數： 5/17頁
文件大?。?/td> 0K
描述： IC INTERFACE ADSL/HDSL2 24-QFN
標準包裝： 90
類型： 驅動器
驅動器/接收器數： 2/0
規程： DSL
電源電壓： 5 V ~ 12 V
安裝類型： 表面貼裝
封裝/外殼： 24-VFQFN 裸露焊盤
供應商設備封裝： 24-QFN（5x4）
包裝： 管件
13
FN7039.2
March 26, 2007
Applications Information
The EL1503A consists of two high-power line driver
amplifiers that can be connected for full duplex differential
line transmission. The amplifiers are designed to be used
with signals up to 4MHz and produce low distortion levels. A
typical interface circuit is shown in Figure 39 below.
The amplifiers are wired with one in positive gain and the
other in a negative gain configuration to generate a
differential output for a single-ended input. They will exhibit
very similar frequency responses for gains of three or
greater and thus generate very small common-mode outputs
over frequency, but for low gains the two drivers RF's need
to be adjusted to give similar frequency responses. The
positive-gain driver will generally exhibit more bandwidth and
peaking than the negative-gain driver.
If a differential signal is available to the drive amplifiers, they
may be wired so:
Each amplifier has identical positive gain connections, and
optimum common-mode rejection occurs. Further, DC input
errors are duplicated and create common-mode rather than
differential line errors.
Input Connections
The EL1503A amplifiers are somewhat sensitive to source
impedance. In particular, they do not like being driven by
inductive sources. More than 100nH of source impedance
can cause ringing or even oscillations. This inductance is
equivalent to about 4” of unshielded wiring, or 6” of
unterminated transmission line. Normal high-frequency
construction obviates any such problem.
Power Supplies & Dissipation
Due to the high power drive capability of the EL1503A, much
attention needs to be paid to power dissipation. The power
that needs to be dissipated in the EL1503A has two main
contributors. The first is the quiescent current dissipation.
The second is the dissipation of the output stage.
The quiescent power in the EL1503A is not constant with
varying outputs. In reality, 7mA of the 12.5mA needed to
power each driver is converted in to output current.
Therefore, in the equation below we should subtract the
average output current, IO, or 7mA, whichever is the lowest.
We’ll call this term IX.
Therefore, we can determine a quiescent current with the
equation:
where:
VS is the supply voltage (VS+ to VS-)
IS is the maximum quiescent supply current (IS+ + IS-)
IX is the lesser of IO or 7mA (generally IX = 7mA)
The dissipation in the output stage has two main
contributors. Firstly, we have the average voltage drop
across the output transistor and secondly, the average
output current. For minimal power dissipation, the user
should select the supply voltage and the line transformer
ratio accordingly. The supply voltage should be kept as low
as possible, while the transformer ratio should be selected
so that the peak voltage required from the EL1503A is close
to the maximum available output swing. There is a trade of
however with the selection of transformer ratio. As the ratio
is increased, the receive signal available to the receivers is
reduced.
Once the user has selected the transformer ratio, the
dissipation in the output stages can be selected with the
following equation:
where:
VS is the supply voltage (VS+ to VS-)
VO is the average output voltage per channel
IO is the average output current per channel
The overall power dissipation (PDISS) is obtained by adding
PDquiescent and PDtransistor.
FIGURE 39. TYPICAL LINE INTERFACE CONNECTION
-
+
-
+
-
+
-
+
RECEIVE
OUT -
RECEIVE
OUT +
DRIVER
INPUT
RG
RF
RF
R
RIN
R
RIN
RF
ROUT
LINE +
RECEIVE
AMPLIFIERS
ZLINE
LINE -
FIGURE 40. DRIVERS WIRED FOR DIFFERENTIAL INPUT
-
+
-
+
2RG
RF
P
Dquiescent
V
S
I
S
2I
X
–
()
×
=
P
Dtransistors
2I
O
V
S
2
-------
×
V
O
–
=
EL1503A
相關PDF資料
PDF描述
VE-J1L-MX-F2 CONVERTER MOD DC/DC 28V 75W
D38999/26SB98SA CONN PLUG 6POS STRAIGHT W/SCKT
D38999/20FJ43SB CONN RCPT 43POS WALL MNT W/SCKT
MS27474E24B35SA CONN RCPT 128POS JAM NUT W/SCKT
MS3120E24-61PW CONN RCPT 61POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
EL1503ACL-T13 功能描述:IC INTERFACE ADSL/HDSL2 24-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
EL1503ACL-T7 功能描述:IC INTERFACE ADSL/HDSL2 24-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
EL1503ACLZ 功能描述:IC INTERFACE ADSL/HDSL2 24-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
EL1503ACLZ-T13 功能描述:IC INTERFACE ADSL/HDSL2 24-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
EL1503ACLZ-T7 功能描述:IC INTERFACE ADSL/HDSL2 24-QFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*