- 您現在的位置：買賣IC網 > PDF目錄5551 > EL2480CSZ (Intersil)IC OP AMP QUAD LP 250MHZ 14-SOIC PDF資料下載
參數資料
| 型號： | EL2480CSZ |
| 廠商： | Intersil |
| 文件頁數： | 2/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OP AMP QUAD LP 250MHZ 14-SOIC |
| 標準包裝： | 55 |
| 放大器類型： | 電流反饋 |
| 電路數： | 4 |
| 轉換速率： | 1200 V/µs |
| -3db帶寬： | 250MHz |
| 電流 - 輸入偏壓： | 16µA |
| 電壓 - 輸入偏移： | 2500µV |
| 電流 - 電源： | 3mA |
| 電流 - 輸出 / 通道： | 55mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 12 V，±1.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1233 (CN2011-ZH PDF) |
10
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same
frequency response as DC levels are changed at the output.
This is especially difficult when driving a standard video load
of 150
, because of the change in output current with DC
level. Until the EL2480, good Differential Gain could only be
achieved by running high idle currents through the output
transistors (to reduce variations in output impedance). These
currents were typically comparable to the entire 3mA supply
current of EL2480 amplifier! Special circuitry has been
incorporated in the EL2480 to reduce the variation of output
impedance with current output. This results in dG and dP
specifications of 0.05% and 0.05° while driving 150
at a
gain of +2.
Video performance has also been measured with a 500
load at a gain of +1. Under these conditions, the EL2480 has
dG and dP specifications of 0.01% and 0.01° respectively
while driving 500
at AV = +1.
Output Drive Capability
This amplifier of the EL2480 is capable of providing a
minimum of ±50mA. These output drive levels are
unprecedented in amplifiers running at these supply currents.
The ±50mA minimum output drive of the EL2480 amplifier
allows swings of ±2.5V into 50
loads.
Driving Cables and Capacitive Loads
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, the back-termination series resistor will decouple
the EL2480 from the cable and allow extensive capacitive
drive. However, other applications may have high capacitive
loads without a back-termination resistor. In these
applications, a small series resistor (usually between 5
and
50
) can be placed in series with the output to eliminate most
peaking. The gain resistor (RG) can then be chosen to make
up for any gain loss which may be created by this additional
resistor at the output. In many cases it is also possible to
simply increase the value of the feedback resistor (RF) to
reduce the peaking.
Current Limiting
The EL2480 has no internal current-limiting circuitry. If any
output is shorted, it is possible to exceed the Absolute
Maximum Ratings for output current or power dissipation,
potentially resulting in the destruction of the device.
Power Dissipation
With the high output drive capability of the EL2480, it is
possible to exceed the 150°C Absolute Maximum junction
temperature under certain very high load current conditions.
Generally speaking, when RL falls below about 25, it is
important to calculate the maximum junction temperature
(TJMAX) for the application to determine if power-supply
voltages, load conditions, or package type need to be
modified for the EL2480 to remain in the safe operating area.
These parameters are calculated as follows:
where:
TMAX = Maximum ambient temperature
θ
JA = Thermal resistance of the package
n = Number of amplifiers in the package
PDMAX = Maximum power dissipation of each amplifier in
the package
PDMAX for each amplifier can be calculated as follows:
where:
VS = Supply voltage
ISMAX = Maximum supply current of 1 amplifier
VOUTMAX = Maximum output voltage of the application
RL = Load resistance
T
JMAX
T
MAX
Θ
JA
nPD
MAX
×
()
+
=
PD
MAX
2
(
V
S
I
SMAX )
V
S
(
- V
OUTMAX )
V
OUTMAX
R
L
----------------------------
×
+
×
=
EL2480
相關PDF資料 |
PDF描述 |
|---|---|
| CRCW06035R11FKEA | RES 5.11 OHM 1/10W 1% 0603 SMD |
| IPL1-105-01-S-D-RA-K | CONN SHROUDED PWR HEADER 10POS |
| SMBJ7.5CA-E3/51 | TVS 600W 7.5V BIDIRECT SMB |
| ISL28408FBZ | IC INTERFACE |
| CRCW06031R78FKEA | RES 1.78 OHM 1/10W 1% 0603 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL2480CSZ | 制造商:Intersil Corporation 功能描述:IC AMP CURRENT MODE FEEDBACK SMD |
| EL2480CSZ-T13 | 功能描述:高速運算放大器 EL2480CSZ 250 MHZ QD CMF OP AMP 5 V RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| EL2480CSZ-T7 | 功能描述:高速運算放大器 EL2480CSZ 250 MHZ QD CMF OP AMP 5 V RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| EL2480-EVM | 制造商:Intersil Corporation 功能描述:250MHz/3mA Current Mode Feedback Amplifier 制造商:P&S 功能描述:250MHz/3mA Current Mode Feedback Amplifier |
| EL25-1/2-ADUL | 制造商:Fuji Electric 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。