- 您現在的位置：買賣IC網 > PDF目錄5285 > EL5132ISZ (Intersil)IC AMP VFA 670MHZ LO NOISE 8SOIC PDF資料下載
參數資料
| 型號： | EL5132ISZ |
| 廠商： | Intersil |
| 文件頁數： | 3/13頁 |
| 文件大小： | 0K |
| 描述： | IC AMP VFA 670MHZ LO NOISE 8SOIC |
| 標準包裝： | 97 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 1 |
| 轉換速率： | 1000 V/µs |
| 增益帶寬積： | 3GHz |
| -3db帶寬： | 670MHz |
| 電流 - 輸入偏壓： | 12µA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 11mA |
| 電流 - 輸出 / 通道： | 140mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
11
FN7382.8
May 4, 2007
less, and disabled when CE is above 4V. Although the logic
levels are not standard TTL, this choice of logic voltages
allows the EL5132 to be enabled by typing CE to ground,
even in 5V single supply applications. The CE pin can be
driving from CMOS outputs.
Supply Voltage Range and Single-Supply
Operation
The EL5132 and EL5133 have been designed to operate
with supply voltages having a span of greater than 5V and
less than 12V. In practical terms, this means that they will
operate on dual supplies ranging from ±2.5V to ±6V. With
single-supply, the EL5132 and EL5133 will operate from 5V
to 12V. To prevent internal circuit latch-up, the slew rate
between the negative and positve supplies must be less
than 1V/s.
As supply voltages continue to decrease, it becomes
necessary to provide input and output voltage ranges that
can get as close as possible to the supply voltages. The
EL5132 and EL5133 have an input range which extends to
within 2V of either supply. So, for example, on ±5V supplies,
the EL5132 and EL5133 have an input range which spans
±3V. The output range of the EL5132 and EL5133 are also
quite large, extending to within 2V of the supply rail. On a
±5V supply, the output is therefore capable of swinging from
-3.1V to +3.1V. Single-supply output range is larger because
of the increased negative swing due to the external pull-
down resistor to ground.
Power Dissipation
With the wide power supply range and large output drive
capability of the EL5132 and EL5133, it is possible to exceed
the 150°C maximum junction temperatures under certain
load and power-supply conditions. It is therefore important to
calculate the maximum junction temperature (TJMAX) for all
applications to determine if power supply voltages, load
conditions, or package type need to be modified for the
EL5132 and EL5133 to remain in the safe operating area.
These parameters are related as follows:
where:
PDMAXTOTAL is the sum of the maximum power
dissipation of each amplifier in the package (PDMAX)
PDMAX for each amplifier can be calculated as follows:
where:
TMAX = Maximum ambient temperature
θ
JA = Thermal resistance of the package
PDMAX = Maximum power dissipation of 1 amplifier
VS = Supply voltage
IMAX = Maximum supply current of 1 amplifier
VOUTMAX = Maximum output voltage swing of the
application
RL = Load resistance
Power Supply Bypassing And Printed Circuit
Board Layout
As with any high frequency devices, good printed circuit
board layout is essential for optimum performance. Ground
plane construction is highly recommended. Pin lengths
should be kept as short as possible. The power supply pins
must be closely bypassed to reduce the risk of oscillation.
The combination of a 4.7F tantalum capacitor in parallel
with 0.1F ceramic capacitor has been proven to work well
when placed at each supply pin. For single supply operation,
where pin 4 (VS-) is connected to the ground plane, a single
4.7F tantalum capacitor in parallel with a 0.1F ceramic
capacitor across pin 8 (VS+).
For good AC performance, parasitic capacitance should be
kept to a minimum. Ground plane construction again should
be used. Small chip resistors are recommended to minimize
series inductance. Use of sockets should be avoided since
they add parasitic inductance and capacitance which will
result in additional peaking and overshoot.
T
JMAX
T
MAX
θ
JA xPDMAXTOTAL
()
+
=
(EQ. 1)
PD
MAX
2*V
S
I
SMAX
V
S
(
- V
OUTMAX )
V
OUTMAX
R
L
----------------------------
×
+
×
=
(EQ. 2)
EL5132, EL5133
相關PDF資料 |
PDF描述 |
|---|---|
| EL5132IS-T13 | IC AMP VFA 670MHZ LO NOISE 8SOIC |
| CU3225K300G2 | VARISTOR 300V RMS 3225 SMD |
| RT0603DRD0782KL | RES 82K OHM 1/10W .5% 0603 SMD |
| CU4032K275G2 | VARISTOR 275V RMS 4032 SMD |
| LPPB081NGCN-RC | CONN HEADER .050" 8POS R/A PCB |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL5132ISZ-T13 | 功能描述:IC AMP VFA 670MHZ LO NOISE 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| EL5132ISZ-T7 | 功能描述:IC VFA 670MHZ ULT LO VOLT 8SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| EL5133 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:670MHz Low Noise Amplifiers |
| EL513-3 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC |
| EL513-30 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC |
發布緊急采購，3分鐘左右您將得到回復。