參數資料
型號: EL5227CR-T13
廠商: Intersil
文件頁數: 5/17頁
文件大?。?/td> 0K
描述: IC BUFFER LP OCT 2.5MHZ 20-TSSOP
標準包裝: 2,500
放大器類型: 緩沖器
電路數: 8
輸出類型: 滿擺幅
轉換速率: 2.2 V/µs
-3db帶寬: 2.5MHz
電流 - 輸入偏壓: 2nA
電壓 - 輸入偏移: 1000µV
電流 - 電源: 1.3mA
電流 - 輸出 / 通道: 120mA
電壓 - 電源,單路/雙路(±): 4.5 V ~ 16.5 V,±2.25 V ~ 8.25 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-TSSOP(0.173",4.40mm 寬)
供應商設備封裝: 20-TSSOP
包裝: 帶卷 (TR)
13
FN7111.4
May 4, 2007
Driving Capacitive Loads
The EL5127, EL5227, EL5327, and EL5427 can drive a wide
range of capacitive loads. As load capacitance increases,
however, the -3dB bandwidth of the device will decrease and
the peaking increase. The buffers drive 10pF loads in
parallel with 10k
Ω with just 1.5dB of peaking, and 100pF
with 6.4dB of peaking. If less peaking is desired in these
applications, a small series resistor (usually between 5
Ω and
50
Ω) can be placed in series with the output. However, this
will obviously reduce the gain slightly. Another method of
reducing peaking is to add a “snubber” circuit at the output.
A snubber is a shunt load consisting of a resistor in series
with a capacitor. Values of 150
Ω and 10nF are typical. The
advantage of a snubber is that it does not draw any DC load
current or reduce the gain.
Power Supply Bypassing and Printed Circuit
Board Layout
As with any high frequency device, good printed circuit
board layout is necessary for optimum performance. Ground
plane construction is highly recommended, lead lengths
should be as short as possible, and the power supply pins
must be well bypassed to reduce the risk of oscillation. For
normal single supply operation, where the VS- pin is
connected to ground, a 0.1F ceramic capacitor should be
placed from VS+ pin to VS- pin. A 4.7F tantalum capacitor
should then be connected from VS+ pin to ground. One
4.7F capacitor may be used for multiple devices. This same
capacitor combination should be placed at each supply pin
to ground if split supplies are to be used.
EL5127, EL5227, EL5327, EL5427
相關PDF資料
PDF描述
V18AUMLA1210NH VARISTOR MULTILAYER 18V 1210 SMD
EL5227CR IC BUFFER LP OCT 2.5MHZ 20-TSSOP
LPPB092CFFN-RC CONN HEADER .050" 18PS DL PCB AU
EL5227CL-T7 IC BUFFER LP OCT 2.5MHZ 24-QFN
153208-2020-RB CONN 2MM SKT 8POS THRU-BRD SMD
相關代理商/技術參數
參數描述
EL5227CR-T7 功能描述:IC BUFFER LP OCT 2.5MHZ 20-TSSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源,單路/雙路(±):1.8 V ~ 5.25 V,±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP,10-MSOP(0.118",3.00mm 寬) 供應商設備封裝:10-MSOP 包裝:管件
EL5227CRZ 功能描述:運算放大器 - 運放 EL5227CRZ OCTALUFR LW PWR RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
EL5227CRZ-T13 功能描述:運算放大器 - 運放 EL5227CRZ OCTALUFR LW PWR RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
EL5227CRZ-T7 功能描述:運算放大器 - 運放 EL5227CRZ OCTALUFR LW PWR RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
EL5228 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:VCOM with Dual Gamma Buffer