- 您現在的位置：買賣IC網 > PDF目錄2148 > EL5420TISZ-T7 (Intersil)IC OPAMP GP RR 12MHZ QD 14SOIC PDF資料下載
參數資料
| 型號： | EL5420TISZ-T7 |
| 廠商： | Intersil |
| 文件頁數： | 4/17頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC OPAMP GP RR 12MHZ QD 14SOIC |
| 標準包裝： | 1,000 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 4 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 12 V/µs |
| 增益帶寬積： | 8MHz |
| -3db帶寬： | 12MHz |
| 電流 - 輸入偏壓： | 2nA |
| 電壓 - 輸入偏移： | 4000µV |
| 電流 - 電源： | 500µA |
| 電流 - 輸出 / 通道： | 70mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 19 V，±2.25 V ~ 9.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 帶卷 (TR) |
12
FN6838.0
September 25, 2009
Applications Information
Product Description
The EL5420T is a high voltage rail-to-rail input-output
amplifier with low power consumption. The EL5420T
contains four amplifiers. Each amplifier exhibits beyond the
rail input capability, rail-to-rail output capability, and is unity
gain stable.
The EL5420T features a slew rate of 12V/s. Also, the
device provides common mode input capability beyond the
supply rails, rail-to-rail output capability, and a bandwidth of
12MHz (-3dB). This enables the amplifiers to offer maximum
dynamic range at any supply voltage.
Operating Voltage, Input and Output Capability
The EL5420T can operate on a single supply or dual supply
configuration. The EL5420T operating voltage ranges from a
minimum of 4.5V to a maximum of 19V. This range allows for
a standard 5V (or ±2.5V) supply voltage to dip to -10%, or a
standard 18V (or ±9V) to rise by +5.5% without affecting
performance or reliability.
The input common-mode voltage range of the EL5420T
extends 500mV beyond the supply rails. Also, the EL5420T
is immune to phase reversal. However, if the common mode
input voltage exceeds the supply voltage by more than 0.5V,
electrostatic protection diodes in the input stage of the
device begin to conduct. Even though phase reversal will not
occur, to maintain optimal reliability it is suggested to avoid
input overvoltage conditions. Figure 28 shows the input
voltage driven 500mV beyond the supply rails and the device
output swinging between the supply rails.
The EL5420T output typically swings to within 50mV of
positive and negative supply rails with load currents of
±5mA. Decreasing load currents will extend the output
voltage range even closer to the supply rails. Figure 29
shows the input and output waveforms for the device in a
unity-gain configuration. Operation is from ±5V supply with a
10k
Ω load connected to GND. The input is a 10V
P-P
sinusoid and the output voltage is approximately 9.9VP-P.
Refer to the “Electrical Specifications” Table beginning on
page 3 for specific device parameters. Parameter variations
with operating voltage, loading and/or temperature are
shown in the “Typical Performance Curves” on page 6.
Output Current
The EL5420T is capable of output short circuit currents of
200mA (source and sink), and the device has built-in
protection circuitry which limits the short circuit current to
±200mA (typical).
To maintain maximum reliability the continuous output
current should never exceed ±70mA. This ±70mA limit is
determined by the characteristics of the internal metal
interconnects. Also, see “Power Dissipation” on page 13 for
detailed information on ensuring proper device operation
and reliability for temperature and load conditions.
Unused Amplifiers
It is recommended that any unused amplifiers be configured
as a unity gain follower. The inverting input should be directly
connected to the output and the non-inverting input tied to
the ground.
Thermal Shutdown
The EL5420T has a built-in thermal protection which
ensures safe operation and prevents internal damage to the
device due to overheating. When the die temperature
reaches +165°C (typical) the device automatically shuts OFF
the outputs by putting them in a high impedance state. When
the die cools by 15°C (typical) the device automatically turns
FIGURE 28. OPERATION WITH BEYOND-THE-RAILS INPUT
1V
/DI
V
VS = ±2.5V, TA = +25°C, AV = 1, VINx = 6VP-P, RL = 10kΩ to GND
INPUT
OUTPUT
100
s/DIV
FIGURE 29. OPERATION WITH RAIL-TO-RAIL INPUT AND
VS = ±5V, TA = +25°C, AV = 1, VINx = 10VP-P, RL = 10kΩ to GND
5V
/DI
V
INPUT
OUT
P
UT
100
s/DIV
EL5420T
相關PDF資料 |
PDF描述 |
|---|---|
| EL5421CY-T7 | IC BUFFER QUAD R-R 12MHZ 10-MSOP |
| EL5421TIYZ | IC BUFFER R-R 12MHZ 10MSOP |
| EL5423CLZ | IC BUFFER I/O 12MHZ 12CH 32-QFN |
| EL5424ILZ-T7 | IC BUFFER LP 12CH 12MHZ 32-QFN |
| EL5427CRZ-T7 | IC BUFFER LP 12CH 2.5MHZ 28TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL5421 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad 12MHz Rail-to-Rail Input-Output Buffer |
| EL5421_07 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Quad 12MHz Rail-to-Rail Input-Output Buffer |
| EL5421C | 制造商:ELANTEC 制造商全稱:ELANTEC 功能描述:Quad 12MHz Rail-to-Rail Input-Output Buffer |
| EL5421CY | 功能描述:IC BUFFER QUAD R-R 12MHZ 10-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
| EL5421CY-T13 | 功能描述:IC BUFFER QUAD R-R 12MHZ 10-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
發布緊急采購，3分鐘左右您將得到回復。