- 您現在的位置：買賣IC網 > PDF目錄362635 > EL5424ILZ-T7 (INTERSIL CORP) 12MHz Rail-to-Rail Buffers + 100mA VCOM Amplifier PDF資料下載
參數資料
| 型號： | EL5424ILZ-T7 |
| 廠商： | INTERSIL CORP |
| 元件分類： | 緩沖放大器 |
| 英文描述： | 12MHz Rail-to-Rail Buffers + 100mA VCOM Amplifier |
| 中文描述： | 12 BUFFER AMPLIFIER, PQCC32 |
| 封裝： | 0.90 MM HEIGHT, ROHS COMPLIANT, PLASTIC, MO-220, QFN-32 |
| 文件頁數： | 9/12頁 |
| 文件大?。?/td> | 589K |
| 代理商： | EL5424ILZ-T7 |
9
UNUSED BUFFERS
It is recommended that any unused buffers have their inputs
tied to the ground plane.
DRIVING CAPACITIVE LOADS
The buffers can drive a wide range of capacitive loads. As
load capacitance increases, however, the -3dB bandwidth of
the device will decrease and the peaking increase. The
buffers drive 10pF loads in parallel with 10k
with just 1.5dB
of peaking, and 100pF with 6.4dB of peaking. If less peaking
is desired in these applications, a small series resistor
(usually between 5
and 50
) can be placed in series with
the output. However, this will obviously reduce the gain
slightly. Another method of reducing peaking is to add a
snubber circuit at the output. A snubber is a shunt load
consisting of a resistor in series with a capacitor. Values of
150
and 10nF are typical. The advantage of a snubber is
that it does not draw any DC load current or reduce the gain.
The Use of V
COM
Amplifier
The V
COM
amplifier is designed to control the voltage on the
back plate of an LCD display. This plate is capacitively
coupled to the pixel drive voltage which alternately cycles
positive and negative at the line rate for the display. Thus the
amplifier must be capable of sourcing and sinking capacitive
pulses of current, which can occasionally be quite large (a
few 100mA for typical applications).
A simple use of the V
COM
amplifier is as a voltage follower,
as illustrated in Figure 23. Here, a voltage, corresponding to
the mid-DAC potential, is generated by a resistive divider
and buffered by the amplifier. The amplifier's stability is
designed to be dominated by the load capacitance, thus for
very short duration pulses (< 1μs) the output capacitor
supplies the current. For longer pulses the V
COM
amplifier
supplies the current. By virtue of its high transconductance
which progressively increases as more current is drawn, it
can maintain regulation within 5mV as currents up to 100mA
are drawn, while consuming only 2mA of quiescent current.
Alternatively, the back plate potential can be generated by a
DAC and the V
COM
amplifier used to buffer the DAC
voltage, with gain if necessary. This is shown in Figure 24. In
this case, the effective transconductance of the feedback is
reduced, thus the amplifier will be more stable, but regulation
will be degraded by the feedback factor.
CHOICE OF OUTPUT CAPACITOR
A 1μF ceramic capacitor with low ESR is recommended for
this amplifier. (For example, GRM42_ 6X7R105K16). This
capacitor determines the stability of the amplifier. Reducing it
will make the amplifier less stable, and should be avoided.
With a 1μF capacitor, the unity gain bandwidth of the
amplifier is close to 1MHz when reasonable currents are
being drawn. (For lower load currents, the gain and hence
bandwidth progressively decreases.) This means the active
trans-conductance is:
This high transconductance indicates why it is important to
have a low ESR capacitor.
If:
then the capacitor will not force the gain to roll off below
unity, and subsequent poles can affect stability. The
recommended capacitor has an ESR of 10m
, but to this
must be added the resistance of the board trace between the
capacitor and the sense connection - therefore this should
be kept short, as illustrated in Figure 21, by the diagonal line
to the capacitor. Also ground resistance between the
capacitor and the base of R
2
must be kept to a minimum.
These constraints should be considered when laying out the
PCB.
1V
1V
10μs
V
S
=±2.5V
T
A
=25°C
V
IN
=6V
P-P
FIGURE 22. OPERATION WITH BEYOND-THE-RAILS INPUT
-
+
R
1
R
2
V
BOOST
V
COM
1μF CERAMIC
LOW ESR
IPCOM
INCOM
V
COM
V
DDCOM
FIGURE 23. V
COM
USED AS A VOLTAGE BUFFER
V
SSCOM
-
+
R
1
R
2
V
BOOST
V
COM
1μF CERAMIC
LOW ESR
FROM DAC
FIGURE 24. V
COM
USED AS A BUFFER WITH GAIN
2
π
1
μ
F
1MHz
×
×
6.28S
=
ESR
6.28
1
>
×
EL5224, EL5324, EL5424
相關PDF資料 |
PDF描述 |
|---|---|
| EL5225IRZ | 10-Channel TFT-LCD Reference Voltage Generator |
| EL5225IRZ-T13 | 10-Channel TFT-LCD Reference Voltage Generator |
| EL5225IRZ-T7 | 10-Channel TFT-LCD Reference Voltage Generator |
| EL5225 | 10-Channel TFT-LCD Reference Voltage Generator(10通道TFT-LCD基準電壓發生器) |
| EL5227 | 2.5MHz 4-, 8-, 10- and 12-Channel Rail-to-Rail Buffers(2.5MHz 4/8/10/12通道軌對軌緩沖器) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL5427 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:2.5MHz 4. 8. 10 & 12 Channel Rail-to-Rail Buffers |
| EL5427CL | 功能描述:IC BUFFER LP 12CH 2.5MHZ 32-QFN RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
| EL5427CL-T13 | 功能描述:IC BUFFER LP 12CH 2.5MHZ 32-QFN RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
| EL5427CL-T7 | 功能描述:IC BUFFER LP 12CH 2.5MHZ 32-QFN RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:LinCMOS™ 放大器類型:通用 電路數:4 輸出類型:- 轉換速率:0.05 V/µs 增益帶寬積:110kHz -3db帶寬:- 電流 - 輸入偏壓:0.7pA 電壓 - 輸入偏移:210µV 電流 - 電源:57µA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):3 V ~ 16 V，±1.5 V ~ 8 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:管件 產品目錄頁面:865 (CN2011-ZH PDF) 其它名稱:296-1834296-1834-5 |
| EL5427CLZ | 功能描述:運算放大器 - 運放 EL5427CLZ 2 5MHZ 12 CH BUFR RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。