- 您現在的位置：買賣IC網 > PDF目錄362657 > ELANSC400-66AC (ADVANCED MICRO DEVICES INC) Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers PDF資料下載
參數資料
| 型號： | ELANSC400-66AC |
| 廠商： | ADVANCED MICRO DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| 中文描述： | 32-BIT, FLASH, 66 MHz, MICROCONTROLLER, PBGA292 |
| 封裝： | PLASTIC, BGA-292 |
| 文件頁數： | 48/132頁 |
| 文件大?。?/td> | 2400K |
| 代理商： | ELANSC400-66AC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁當前第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁
48
élanSC400 and élanSC410 Microcontrollers Data Sheet
Notes:
1.
The shared GPIO20–GPIO15, GPIO_CS14–GPIO_CS13, and PC Card battery signals:
As GPIO_CSxs, the signals are active in Suspend mode: that is, if they are inputs before Suspend, they are still inputs during
Suspend (the GPIO_CSs can be used to wake up the system); if they are outputs before Suspend, they are still outputs during
Suspend (the GPIO_CSs can be programmed to change state by mode). As inputs, the pullup or pulldown on the signal can be
disabled; if disabled, it is disabled in all modes. When the signal is an output, the built-in resistors are automatically disabled.
When enabled, the Latched Battery Low Detect function (LBL2) that is shared on GPIO19 is an output in all modes; there are
no pullup or pulldown resistors active.
On the élanSC400 microcontroller, the PC Card functions shared on these pins are programmable by PC Card socket; the
pin multiplexing options are explained earlier in this document. For the PC Card power control (PCMA_VCC, PCMA_VPP1,
PCMA_VPP2, PCMB_VCC, PCMB_VPP1, PCMB_VPP2), the signals are outputs for each mode.
For the second Card Detect (CD_A2):
–Reset invokes pullup.
–During normal operation, the pullup resistor can be disabled by a register bit.
–During Suspend mode, the input will have a pulldown if the PC Card Socket A interface is programmed to be powered off
in Suspend mode (Power-Down Group G). If the socket is not programmed to be powered off in Suspend mode, the input
will have the same state as when operating: the pullup is programmable to be enabled or not.
2. The PC Card signals MCEL_B, MCEH_B, RST_B, REG_B, CD_B,
RDY_B
, BVD1_B, BVD2_B, WP_B, CD_A2,
PCMB_VPP2, PCMB_VPP1, PCMB_VCC, PCMA_VPP1, PCMA_VPP2, and PCMA_VCC are not supported on the
élanSC410 microcontroller.
3. The shared parallel port, PC Card Socket B control, and GPIO signals:
–These signals default to the GPIO interface on reset.
–As a parallel port in Suspend mode, these signals are programmable to accommodate the parallel port powered up or
down.
–As PC Card control on the élanSC400 microcontroller, these signals have the same features as the Socket A control
signals.
–As GPIOs, these signals are not handled specially in Suspend, they remain the same as they were when the chip was
active (i.e., they remain as inputs with the pullup enabled or not, or continue to drive out the same value if they were
outputs).
Summary:
Shared parallel port/PC Card Socket B/GPIO signals: Built-in pullup and pulldown resistors that are invoked by:
–Reset invokes pullups
–As parallel port signals:
Operating: pullups are enabled if not EPP mode. Outputs without pullup or pulldowns if EPP mode.
Suspend: pullups are enabled, unless the parallel port is programmed to be powered off in Suspend mode, in which
case pulldowns are enabled.
If EPP mode is enabled for the parallel port, the outputs are driven out at their last value in Suspend mode.
–As PC Card Socket B signals (élanSC400 microcontroller only):
Operating: outputs have no pullups or pulldowns; inputs have pullups that can be disabled by programming a bit.
Suspend: outputs are driven out inactive with no pullups or pulldowns unless the PC Card Socket B is programmed
to be powered off in Suspend mode; then the outputs go to three-state with pulldown resistors; inputs will be the
same as they were when operating, with a pullup resistor that can be disabled by programming, unless the PC Card
Socket B is programmed to be powered off in Suspend mode (Power-Down Group H), in which case the inputs have
pulldown resistors enabled.
–As GPIO signals:
Operating or Suspend: as outputs they have no pullups or pulldowns; as inputs they have pullups that can be dis-
abled by programming a bit; no change of state when the system goes to Suspend.
相關PDF資料 |
PDF描述 |
|---|---|
| ELANSC400-66AI | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-100AC | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-100AI | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-33AC | Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC410-33AI | 5566-12BGS /N/MINI FIT CONN HOUS ASSY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ELANSC400-66AI | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:Single-Chip, Low-Power, PC/AT-Compatible Microcontrollers |
| ELANSC400ANDELANSC410 | 制造商:AMD 制造商全稱:Advanced Micro Devices 功能描述:ElanSC400 and ElanSC410 - Single-Chip. Low-Power. PC/AT-Compatible Microcontrollers |
| ELANSC410 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:ElanSC410 - ElanSC410 Block Diagram |
| ELANSC410-100AC | 制造商:Advanced Micro Devices 功能描述:MCU 16-Bit/32-Bit Elan CISC ROMLess 3.3V 292-Pin BGA |
| ELANSC410-100ACAD | 制造商:Advanced Micro Devices 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。