- 您現在的位置：買賣IC網 > PDF目錄362688 > EM78P447NAP (ELAN Microelctronics Corp .) 8-BIT MICRO-CONTROLLER PDF資料下載
參數資料
| 型號： | EM78P447NAP |
| 廠商： | ELAN Microelctronics Corp . |
| 英文描述： | 8-BIT MICRO-CONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 19/55頁 |
| 文件大小： | 1730K |
| 代理商： | EM78P447NAP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁
EM78P447S
OTP ROM
(A) Any of the wake-up pins is “0” as illustrated in Figure. 5. Upon waking, the controller will continue
to execute the succeeding address. Under this case, before entering SLEEP2 MODE, the
wake-up function of the trigger sources (P60~P67 and P74~P75) should be selected (e.g., input
pin) and enabled (e.g., pull-high, wake-up control). It should be noted that after waking up, the
WDT is enabled if the Code Option bit ENWDT is “0”. The WDT operation (to be enabled or
disabled) should be appropriately controlled by software after waking up.
(B) WDT time-out (if enabled) or external reset input on /RESET pin will trigger a controller reset.
Table 4 Usage of Sleep1 and Sleep2 Mode
Usage of Sleep1 and Sleep2 Mode
SLEEP2
SLEEP1
(a) Before SLEEP
1. Set Port6 or P74 or P75 Input
2. Enable Pull-High and set WDT prescaler over
1:1 (Set CONT.7 and CONT.3 ~ CONT.0)
3. Enable Wake-up (Set IOCB or IOCE.0)
4. Execute Seep2 (Set IOCE.4)
(b) After Wake-up
1. Next instruction
2. Disable Wake-up
3. Disable WDT (Set IOCE.5)
(a) Before SLEEP
1. Execute SLEP instruction
(b) After Wake-up
1. Reset
If Port6 Input Status Changed Wake-up is used to wake-up the EM78P447S (Case [a] above), the
following instructions must be executed before entering SLEEP2 mode:
MOV
A, @11111111b ; Set Port6 input
IOW
R6
MOV
A, @0xxx1010b ; Set Port6 pull-high, WDT prescaler, prescaler must set over 1:1
CONTW
MOV
A, @00000000b ; Enable Port6 wake-up function
IOW
RB
MOV
A, @xx00xxx1b ; Enable SLEEP2
IOW
RE
After Wake-up
NOP
MOV
A, @11111111b ; Disable Port6 wake-up function
IOW
RB
MOV
A, @ xx01xxx1b ; Disable WDT
IOW
RE
Note:
After waking up from the SLEEP2 mode, WDT is automatically enabled. The WDT enabled/disabled
operation after waking up from SLEEP2 mode should be appropriately defined in the software.
To avoid reset from occurring when the port6 status changed interrupt enters into interrupt vector or
is used to wake-up the MCU, the WDT prescaler must be set above 1:1 ratio.
This specification is subject to change without prior notice.
06.25.2003 (V1.1)
19
相關PDF資料 |
PDF描述 |
|---|---|
| EM78P447NAS | 8-BIT MICRO-CONTROLLER |
| EM78P451SWM | 8-Bit Microcontroller with OTP ROM |
| EM78P451SAQ | 8-Bit Microcontroller with OTP ROM |
| EM78P451S | Quad, Serial, 8-Bit DACs with Rail-to-Rail Outputs |
| EM78P451SP | 8-Bit Microcontroller with OTP ROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EM7A8620 | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Voice over IP |
| EM7G | 制造商:GULFSEMI 制造商全稱:Gulf Semiconductor 功能描述:ULTRAFAST EFFICIENT PLASTIC SILICON RECTIFIER VOLTAGE： 1000V CURRENT： 1.0A |
| EM800 | 制造商:EDI 制造商全稱:Electronic devices inc. 功能描述:HIGH VOLTAGE HIGH CURRENT MINIATURE RECTIFIERS |
| EM8000EHP | 制造商:JDSU 制造商全稱:JDS Uniphase Corporation 功能描述:The industrya??s most compact 100 G test solution |
| EM800-DCM | 制造商:MRV 制造商全稱:MRV 功能描述:LambdaDriver Dispersion Compensation Module (EM800/1600-DCM and DCMD) |
發布緊急采購，3分鐘左右您將得到回復。