- 您現在的位置：買賣IC網 > PDF目錄362688 > EM78P809NS (ELAN Microelctronics Corp .) 8-BIT MICROCONTROLLER PDF資料下載
參數資料
| 型號： | EM78P809NS |
| 廠商： | ELAN Microelctronics Corp . |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-BIT MICROCONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 52/75頁 |
| 文件大?。?/td> | 531K |
| 代理商： | EM78P809NS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁當前第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁
EM78P809N
8-Bit Microcontroller
48
Product Specification (V1.0) 07.26.2005
(This specification is subject to change without further notice)
The Watchdog timer and prescaler are cleared.
Upon power on, the upper 2 bits of R3 are cleared.
Upon power on, the upper 2 bits of R4 are cleared.
Upon power on, the upper 3 bits of R5 are cleared.
The bits of CONT register are set to all “1” except bit 6 (INT flag).
ISFR0, ISFR1, ISFR2 register and IMR1, IMR2 registers are cleared.
The controller has two modes for power saving.
(1) SLEEP mode: R5 (SIS) = 1, SLEP instruction.
The internal oscillator is turned off and all system operation is halted.
(2) IDLE mode: R5 (SIS)= 0, SLEP instruction
The CPU core halts but the on-chip peripheral and oscillator circuit remain active.
4.14.2 Wake-up from SLEEP Mode:
(1) External /SLEEP pin
The controller will be waken up and execute the next instruction after entering SLEEP
mode. All the registers will maintain their original values before “SLEP” instruction was
executed.
(2) /RESET pin pull low
This will reset the controller and starts the program at address zero.
(3) WDT time out
This will reset the controller and run the program at address zero.
4.14.3 Wake-up from IDLE mode:
(1) All interrupt
In all these cases, user should always enable the circuit before entering IDLE mode.
After wake-up, all registers will maintain their original values before entering “SLEP”
instruction, then service an interrupt subroutine or proceed with next instruction by
setting individual interrupt enable bit. After servicing an interrupt sub-routine (“RETI”
instruction), the program will jump from “SLEP” instruction to the next instruction.
(2) /RESET pin pull low
This will reset the controller and run the program at address zero.
(3) WDT time out
This will reset the controller and run the program at address zero.
相關PDF資料 |
PDF描述 |
|---|---|
| EM78P860 | 8 -BIT MICRO-CONTROLLER |
| EM78P870 | 8 BIT MICROCONTROLLER |
| EM78Q156A | 8-Bit Micro-Controller for General-Purpose Product(工作電壓2.5V-6.5V的8位微控制器) |
| EM83010 | I/O EXPANDER |
| EM83040A | LCD CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EM7A8620 | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:Voice over IP |
| EM7G | 制造商:GULFSEMI 制造商全稱:Gulf Semiconductor 功能描述:ULTRAFAST EFFICIENT PLASTIC SILICON RECTIFIER VOLTAGE： 1000V CURRENT： 1.0A |
| EM800 | 制造商:EDI 制造商全稱:Electronic devices inc. 功能描述:HIGH VOLTAGE HIGH CURRENT MINIATURE RECTIFIERS |
| EM8000EHP | 制造商:JDSU 制造商全稱:JDS Uniphase Corporation 功能描述:The industrya??s most compact 100 G test solution |
| EM800-DCM | 制造商:MRV 制造商全稱:MRV 功能描述:LambdaDriver Dispersion Compensation Module (EM800/1600-DCM and DCMD) |
發布緊急采購，3分鐘左右您將得到回復。