- 您現在的位置：買賣IC網 > PDF目錄362695 > EN25F40-75HCP (Eon Silicon Solution Inc.) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | EN25F40-75HCP |
| 廠商： | Eon Silicon Solution Inc. |
| 元件分類： | FLASH |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 7/33頁 |
| 文件大小： | 477K |
| 代理商： | EN25F40-75HCP |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
TABLE 3. Protected Area Sizes Sector Organization
This Data Sheet may be revised by subsequent versions 2004 Eon Silicon Solution, Inc., www.essi.com.tw
or modifications due to changes in technical specifications.
Rev. B, Issue Date: 2007/05/09
EN25F40
Status Register
Content
BP2
Bit
Bit
1
1
1
1
1
0
1
0
0
1
0
1
0
0
0
0
Hold Function
The Hold (HOLD) signal is used to pause any serial communications with the device without resetting the
clocking sequence. However, taking this signal Low does not terminate any Write Status Register,
Program or Erase cycle that is currently in progress.
To enter the Hold condition, the device must be selected, with Chip Select (CS#) Low. The Hold condition
starts on the falling edge of the Hold (HOLD) signal, provided that this coincides with Serial Clock (CLK)
being Low (as shown in Figure 4.).
The Hold condition ends on the rising edge of the Hold (HOLD) signal, provided that this coincides with
Serial Clock (CLK) being Low.
If the falling edge does not coincide with Serial Clock (CLK) being Low, the Hold condition starts after
Serial Clock (CLK) next goes Low. Similarly, if the rising edge does not coincide with Serial Clock (CLK)
being Low, the Hold condition ends after Serial Clock (CLK) next goes Low. (This is shown in Figure 4.).
During the Hold condition, the Serial Data Output (DO) is high impedance, and Serial Data Input (DI) and
Serial Clock (CLK) are Don’t Care.
Normally, the device is kept selected, with Chip Select (CS#) driven Low, for the whole duration of the
Hold condition. This is to ensure that the state of the internal logic remains unchanged from the moment
of entering the Hold condition.
If Chip Select (CS#) goes High while the device is in the Hold condition, this has the effect of resetting the
internal logic of the device. To restart communication with the device, it is necessary to drive Hold (HOLD)
High, and then to drive Chip Select (CS#) Low. This prevents the device from going back to the Hold
condition.
Figure 4. Hold Condition Waveform
Memory Content
Addresses
000000h-0FFFFFh
000000h-0FFFFFh
000000h-0FFFFFh
000000h-0FFFFFh
040000h-07FFFFh
060000h-07FFFFh
070000h-07FFFFh
None
BP1
BP0
Bit
1
0
1
0
1
0
1
0
Protect Blocks
Density(KB)
512KB
512KB
512KB
512KB
256KB
128KB
64KB
None
Portion
All
All
All
All
4 to 7
6 to 7
7
None
All
All
All
All
Upper 1/2
Upper 1/4
Upper 1/8
None
相關PDF資料 |
PDF描述 |
|---|---|
| EN25F40-75HI | 4 Mbit Uniform Sector, Serial Flash Memory |
| EN25F40-75HIP | 4 Mbit Uniform Sector, Serial Flash Memory |
| EN25F40-75QC | 4 Mbit Uniform Sector, Serial Flash Memory |
| EN25F40-75QCP | 4 Mbit Uniform Sector, Serial Flash Memory |
| EN25F40-75QI | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EN25F40-75HI | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:4 Mbit Serial Flash Memory with 4Kbytes Uniform Sector |
| EN25F40-75HIP | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:4 Megabit Serial Flash Memory with 4Kbytes Uniform Sector |
| EN25F40-75QC | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:4 Mbit Serial Flash Memory with 4Kbytes Uniform Sector |
| EN25F40-75QCP | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:4 Mbit Serial Flash Memory with 4Kbytes Uniform Sector |
| EN25F40-75QI | 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:4 Mbit Serial Flash Memory with 4Kbytes Uniform Sector |
發布緊急采購，3分鐘左右您將得到回復。