- 您現在的位置：買賣IC網 > PDF目錄171850 > EP53F8QI (ENPIRION INC) PDF資料下載
參數資料
| 型號： | EP53F8QI |
| 廠商： | ENPIRION INC |
| 元件分類： | 穩壓器 |
| 中文描述： | 1.5 A SWITCHING REGULATOR, 4000 kHz SWITCHING FREQ-MAX, QCC16 |
| 封裝： | 3 X 3 MM, 1.10 MM HEIGHT, HAOLOGEN FREE AND ROHS COMPLIANT, QFN-16 |
| 文件頁數： | 11/11頁 |
| 文件大?。?/td> | 259K |
| 代理商： | EP53F8QI |
01542
4/3/2009
Rev:A
EP53F8QI
Enpirion 2009 all rights reserved, E&OE
9
www.enpirion.com
Application Information
Setting the Output Voltage
Figure 5: Typical Application Circuit
The EP53F8QI uses a simple resistor divider to
program the output voltage.
Referring to Figure 5, use 237 k, 1% or better
for the upper resistor (Ra). The value of the
bottom resistor (Rb) in k is given as:
Ω
=
k
V
Rb
OUT
6
.
0
2
.
142
Where VOUT is the output voltage. Rb should
also be a 1% or better resistor.
A 5.0pF MLCC capacitor is required in parallel
with Ra for compensation.
Input and Output Capacitor Selection
Low ESR MLC capacitors with X5R or X7R or
equivalent dielectric should be used for input
and output capacitors. Y5V or equivalent
dielectrics lose too much capacitance with
frequency,
DC
bias,
and
temperature.
Therefore, they are not suitable for switch-
mode DC-DC converter filtering, and must be
avoided.
The input filter capacitor requirement is a 10
F, 10V 0805 MLCC capacitor in parallel with a
680pF MLCC capacitor. The 680pF capacitor
provides additional high frequency decoupling
and is manditory. The 680pF capacitor must
be placed closest to the EP53F8QI as shown
in Figure 5.
The output filter capacitor requirement is a
22 F, 6.3V, 0805 MLCC for most applications.
The output ripple can be reduced by using 2 x
22 F, 6.3V, 0805 MLC capacitors.
AVIN Decoupling
AVIN should be connected to PVIN using a
10 resistor. An 0402 or smaller case size is
recommended for this resistor. A 1 F, 10 V,
0402 MLC capacitor should be connected from
AVIN to AGND to provide high frequency
decoupling for the control circuitry supply for
optimal performance.
POK Pull Up Resistor Selection
If the POK signal is required for the application.
The POK pin must be pulled up through a
resistor to any voltage source that can be as
high as VIN. The simplest way is to connect
POK to the power input of the converter
through a resistor. A 100 k pull up resistor is
recommended
for
most
applications
for
minimal current drain from the voltage source
and good noise immunity. POK can sink up to
5mA.
Layout Recommendation
Please refer to the EP53F8QI product page at
www.enpirion.com for the most current device
layout recommendation, Gerber files, and other
manufacturing guidelines.
相關PDF資料 |
PDF描述 |
|---|---|
| EPC1079HE1-G | 2-OUTPUT DC-DC UNREG PWR SUPPLY MODULE |
| EPC1083HE1-G | 1-OUTPUT DC-DC UNREG PWR SUPPLY MODULE |
| EPC1013PE1-G | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| EPC1054H | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| EPG5335S | T-1 3/4 SINGLE COLOR LED, GREEN, 5 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EP53F8QI-E | 功能描述:電源管理IC開發工具 Eval Board EP53F8QI 1500mA Sync Buck Con RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| EP53F8QI-T | 制造商:ENPIRION 制造商全稱:ENPIRION 功能描述:1500 mA Synchronous Buck PWM DC-DC Converter with Integrated Inductor |
| EP550 | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:EP550 SDIO/SD Memory/MMC Host Controller |
| EP5502T | 制造商:ViewSonic Corp. 功能描述:55" EPOSTER, FULL HD 1920X1080 |
| EP5555T | 制造商:ViewSonic Corp. 功能描述:55" DUAL SIDED EPOSTER, SINGLE SCREEN |
發布緊急采購，3分鐘左右您將得到回復。